PIC32ソフト

Harmonyの設定

ADC

I2C

TIMER

USART

System Services – Interrupts

Pin Diagram

Pin Settings

・コードの編集前に文字コードをShift-Jisに変更します。

・MainボードとSubボードのコードをコンパイラ擬似命令で切り替えます。ポートの設定が異なるのでsys_ports_static.cの以下の部分をコメントアウトしておいて、system_init.cで切り替えます。

・System init.cを編集します。

void SYS_Initialize　の中にあります。

//
//
/* Initialize System Services */
    SYS_PORTS_Initialize();

#if ROSEN_NUM == 0
    _TRISB10 = 0;
#else
    PLIB_PORTS_RemapInput(PORTS_ID_0, INPUT_FUNC_INT1, INPUT_PIN_RPB10);
#endif

    /*** Interrupt Service Initialization Code ***/
    SYS_INT_Initialize();

#if ROSEN_NUM != 0
    /*Setup the INT_SOURCE_EXTERNAL_1 and Enable it*/
    SYS_INT_VectorPrioritySet(INT_VECTOR_INT1, INT_PRIORITY_LEVEL6);
    SYS_INT_VectorSubprioritySet(INT_VECTOR_INT1, INT_SUBPRIORITY_LEVEL0);
    SYS_INT_ExternalInterruptTriggerSet(INT_EXTERNAL_INT_SOURCE1, INT_EDGE_TRIGGER_FALLING);
    SYS_INT_SourceEnable(INT_SOURCE_EXTERNAL_1);
#endif

/* Initialize System Services */

SYS_PORTS_Initialize();

#if ROSEN_NUM == 0

_TRISB10 = 0;

#else

PLIB_PORTS_RemapInput(PORTS_ID_0, INPUT_FUNC_INT1, INPUT_PIN_RPB10);

#endif

/*** Interrupt Service Initialization Code ***/

SYS_INT_Initialize();

#if ROSEN_NUM != 0

/*Setup the INT_SOURCE_EXTERNAL_1 and Enable it*/

SYS_INT_VectorPrioritySet(INT_VECTOR_INT1, INT_PRIORITY_LEVEL6);

SYS_INT_VectorSubprioritySet(INT_VECTOR_INT1, INT_SUBPRIORITY_LEVEL0);

SYS_INT_ExternalInterruptTriggerSet(INT_EXTERNAL_INT_SOURCE1, INT_EDGE_TRIGGER_FALLING);

SYS_INT_SourceEnable(INT_SOURCE_EXTERNAL_1);

#endif

ソースファイルの追加

Header Files-Appに “atc.h” を追加

atc.h

//
//2022_0903
//
#define TR_COUNT 3      //列車数
#define ROSEN_NUM 0   //路線（ボード）番号
#define BOARD_COUNT 3     //ボード数

#define RX_BYTE 128     //RS232C受信バイト数
#define TX_BYTE 230     //RS232C送信バイト数
#define RX_DATA_BYTE 12 //1列車当たりの受信バイト数
#define TX_DATA_BYTE 12 //1列車当たりの送信バイト数
#define SPEED_MAX 0x3C0      //3C0 timer piriod

//I2C用変数    
DRV_HANDLE hi2c;
DRV_I2C_BUFFER_HANDLE bhi2c;
//USART用変数 
DRV_HANDLE handleUSART0;

bool ext_int_enable;

//16bitのINT型の上位H byte、下位L byte読み込み用共用体

union byte_access {
    int INT; // Int Access

    struct { // byte　Access
        unsigned char L;
        unsigned char H;
    } BYTE;
};

//位置情報の構造体

struct PSI_BIT {
    unsigned char KUKAN : 3; /* 区間 Bit 0-2 */
    unsigned char ROSEN : 3; /* 路線 Bit 3-5 */
    unsigned char SOU : 1; /* 相   Bit 6   */
    unsigned char DIR : 1; /* 方向 Bit 7   */
};

struct STATUS_BIT {
    unsigned char CHG : 1; //区間変化
    unsigned char REV : 1; //逆転
    unsigned char SP_MANU : 1; //スピード制御
    unsigned char DUMY : 3; //DUMY
    unsigned char SLOW : 1; //減速
    unsigned char SAFE : 1; //安全
};
//列車の位置情報の構造体

struct st_position {
    //現在位置

    union { /* Position */
        unsigned char BYTE; /* Byte Access */
        struct PSI_BIT BIT; /* Bit  Access */
    } NOW;
    //前の位置

    union { /* Position */
        unsigned char BYTE; /* Byte Access */
        struct PSI_BIT BIT; /* Bit  Access */
    } BEFORE;

    //次の位置

    union { /* Position */
        unsigned char BYTE; /* Byte Access */
        struct PSI_BIT BIT; /* Bit  Access */
    } NEXT;

    //次々の位置

    union { /* Position */
        unsigned char BYTE; /* Byte Access */
        struct PSI_BIT BIT; /* Bit  Access */
    } ANEXT;

    union {
        unsigned char BYTE; /* Byte Access */
        struct STATUS_BIT BIT; /* Bit  Access */
    } STATUS;

    int speed;

    union byte_access speed_cont;

    int speed_err;
    int speed_peak;
    int err_th;

    int mascon;

    unsigned char henka;
    //unsigned char safe;
    union byte_access speed_ret; //読み取りスピード
    union byte_access speed_ret_rx; //読み取りスピード
    union byte_access speed_ret_tx; //読み取りスピード

    unsigned char point;
    unsigned char yard;

    union byte_access speed_rx;

    unsigned char REC_NOW;
    unsigned char REC_NEXT;
    unsigned char REC_BEFORE;
    
    
};


//監視区間設定用の共用体

union scan_port {
    unsigned char BYTE; /* Byte Access */

    struct {
        unsigned char DUMMY : 2; /* Bit 0-1 */
        unsigned char KUKAN : 3; /* Bit 2-4 監視区間*/
        unsigned char DISABLE : 1; /* Bit 5   */
        unsigned char B6 : 1; /* Bit 6   */
    } BIT;

};





unsigned char EnableBit[] = {1, 2, 4, 8, 16, 32, 64, 128};
unsigned int int_counter; //インタラプトカウンタ
unsigned int speed_pw[2]; //スピードパルス幅
struct st_position train[TR_COUNT]; //列車位置情報
struct st_position* train_sou[2];
unsigned char cont_train[2]; //制御する列車番号
unsigned char kukan[2]; //区間
unsigned char kanshi_now[2]; //スピード読み込み用
unsigned char kanshi_before[2]; //スピード読み込み用
union scan_port kanshi; //区間監視用

union byte_access adc_ret; //ADC値
union byte_access debug1; //ADC値
union byte_access debug2; //ADC値

int gnd_adc;

union byte_access gnd_level;

unsigned char rx_data[RX_BYTE];
unsigned char tx_data[TX_BYTE];

unsigned char receive_data; //通信用受信データ
unsigned char send_data; //通信用送信データ
unsigned char comm_data[128]; //通信用メモリ
unsigned int comm_counter; //通信用インタラプトカウンタ
unsigned char board_num; //ボード番号

unsigned char point_req; //ポイントリクエスト
unsigned char yard_req; //ポイントリクエスト

int err_buff[2][16]; 
union byte_access err_avr[2]; 
union byte_access timer_value; 
union byte_access log_1;
union byte_access log_2;
union byte_access osc_trg;
unsigned char chg_disable;
unsigned char same_dir;
unsigned int ext_time;
unsigned char same_dir_mode;
unsigned char inc_interval;
unsigned int ext_pwr[2];
unsigned char section1;
unsigned char section2;
union byte_access int_count1;
union byte_access int_count2;
unsigned char both_off;
int sp_w1;
int sp_w2;

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

//2022_0903

#define TR_COUNT 3 //列車数

#define ROSEN_NUM 0 //路線（ボード）番号

#define BOARD_COUNT 3 //ボード数

#define RX_BYTE 128 //RS232C受信バイト数

#define TX_BYTE 230 //RS232C送信バイト数

#define RX_DATA_BYTE 12 //1列車当たりの受信バイト数

#define TX_DATA_BYTE 12 //1列車当たりの送信バイト数

#define SPEED_MAX 0x3C0 //3C0 timer piriod

//I2C用変数

DRV_HANDLE hi2c;

DRV_I2C_BUFFER_HANDLE bhi2c;

//USART用変数

DRV_HANDLE handleUSART0;

bool ext_int_enable;

//16bitのINT型の上位H byte、下位L byte読み込み用共用体

union byte_access {

int INT; // Int Access

struct { // byte　Access

unsigned char L;

unsigned char H;

} BYTE;

};

//位置情報の構造体

struct PSI_BIT {

unsigned char KUKAN : 3; /* 区間 Bit 0-2 */

unsigned char ROSEN : 3; /* 路線 Bit 3-5 */

unsigned char SOU : 1; /* 相 Bit 6 */

unsigned char DIR : 1; /* 方向 Bit 7 */

};

struct STATUS_BIT {

unsigned char CHG : 1; //区間変化

unsigned char REV : 1; //逆転

unsigned char SP_MANU : 1; //スピード制御

unsigned char DUMY : 3; //DUMY

unsigned char SLOW : 1; //減速

unsigned char SAFE : 1; //安全

};

//列車の位置情報の構造体

struct st_position {

//現在位置

union { /* Position */

unsigned char BYTE; /* Byte Access */

struct PSI_BIT BIT; /* Bit Access */

} NOW;

//前の位置

union { /* Position */

unsigned char BYTE; /* Byte Access */

struct PSI_BIT BIT; /* Bit Access */

} BEFORE;

//次の位置

union { /* Position */

unsigned char BYTE; /* Byte Access */

struct PSI_BIT BIT; /* Bit Access */

} NEXT;

//次々の位置

union { /* Position */

unsigned char BYTE; /* Byte Access */

struct PSI_BIT BIT; /* Bit Access */

} ANEXT;

union {

unsigned char BYTE; /* Byte Access */

struct STATUS_BIT BIT; /* Bit Access */

} STATUS;

int speed;

union byte_access speed_cont;

int speed_err;

int speed_peak;

int err_th;

int mascon;

unsigned char henka;

//unsigned char safe;

union byte_access speed_ret; //読み取りスピード

union byte_access speed_ret_rx; //読み取りスピード

union byte_access speed_ret_tx; //読み取りスピード

unsigned char point;

unsigned char yard;

union byte_access speed_rx;

unsigned char REC_NOW;

unsigned char REC_NEXT;

unsigned char REC_BEFORE;

};

//監視区間設定用の共用体

union scan_port {

unsigned char BYTE; /* Byte Access */

struct {

unsigned char DUMMY : 2; /* Bit 0-1 */

unsigned char KUKAN : 3; /* Bit 2-4 監視区間*/

unsigned char DISABLE : 1; /* Bit 5 */

unsigned char B6 : 1; /* Bit 6 */

} BIT;

};

unsigned char EnableBit[] = {1, 2, 4, 8, 16, 32, 64, 128};

unsigned int int_counter; //インタラプトカウンタ

unsigned int speed_pw[2]; //スピードパルス幅

struct st_position train[TR_COUNT]; //列車位置情報

struct st_position* train_sou[2];

unsigned char cont_train[2]; //制御する列車番号

unsigned char kukan[2]; //区間

unsigned char kanshi_now[2]; //スピード読み込み用

unsigned char kanshi_before[2]; //スピード読み込み用

union scan_port kanshi; //区間監視用

union byte_access adc_ret; //ADC値

union byte_access debug1; //ADC値

union byte_access debug2; //ADC値

int gnd_adc;

union byte_access gnd_level;

unsigned char rx_data[RX_BYTE];

unsigned char tx_data[TX_BYTE];

unsigned char receive_data; //通信用受信データ

unsigned char send_data; //通信用送信データ

unsigned char comm_data[128]; //通信用メモリ

unsigned int comm_counter; //通信用インタラプトカウンタ

unsigned char board_num; //ボード番号

unsigned char point_req; //ポイントリクエスト

unsigned char yard_req; //ポイントリクエスト

int err_buff[2][16];

union byte_access err_avr[2];

union byte_access timer_value;

union byte_access log_1;

union byte_access log_2;

union byte_access osc_trg;

unsigned char chg_disable;

unsigned char same_dir;

unsigned int ext_time;

unsigned char same_dir_mode;

unsigned char inc_interval;

unsigned int ext_pwr[2];

unsigned char section1;

unsigned char section2;

union byte_access int_count1;

union byte_access int_count2;

unsigned char both_off;

int sp_w1;

int sp_w2;

・Souse Files – appに “lcd.c” を追加

lcd.c

//
//
//2022_0612  lcd.c

#include "system/common/sys_common.h"
#include "app.h"
#include "system_definitions.h"

#define ADR 0x7C
void LCD_cmd(char);
void LCD_int(void);
void LCD_str(char *);
void LCD_dat(char);
void LCD_hex(char);
void LCD_posyx(char, char);

void BSP_DelayMs(unsigned short);
void BSP_DelayUs(unsigned short);

uint8_t data[5];

//遅延調整用関数（ｍｓ）
void BSP_DelayMs(unsigned short milliseconds) {
    unsigned long time;
    time = _CP0_GET_COUNT(); //Read Core Timer
    time += (SYS_CLK_FREQ / 2 / 1000) * milliseconds; //calc the Stop Time
    while ((long) (time - _CP0_GET_COUNT()) > 0) {
    };
}

//遅延調整用関数（μｓ）
void BSP_DelayUs(unsigned short microseconds) {
    unsigned long time;
    time = _CP0_GET_COUNT(); //Read Core Timer
    time += (SYS_CLK_FREQ / 2 / 1000000) * microseconds; //calc the Stop Time
    while ((long) (time - _CP0_GET_COUNT()) > 0) {
    };
}

void LCD_cmd(char cmd) {
    data[0] = 0x80;
    data[1] = cmd;

    bhi2c = DRV_I2C_Transmit(hi2c, ADR, data, 2, NULL);//I2C送信
    while (DRV_I2C_TransferStatusGet(hi2c, bhi2c) != DRV_I2C_BUFFER_EVENT_COMPLETE); /*I2C完了待ち*/

    
    if (cmd & 0xFC) // LCDのコマンドにより待ち時間が違う
        BSP_DelayUs(60); // 60usec
    else
        BSP_DelayMs(3); // 3msec

}

void LCD_int(void) {
    BSP_DelayMs(100); 

    LCD_cmd(0x38);
    LCD_cmd(0x39);
    LCD_cmd(0x14);
    LCD_cmd(0x73); //7A(forAQM1602)
    LCD_cmd(0x56); //54(forAQM1602)
    LCD_cmd(0x6C);

    BSP_DelayMs(200);

    LCD_cmd(0x0C); //Disp ON/OFF
    LCD_cmd(0x01);// Clear Display

    BSP_DelayUs(1100);

}

//文字列表示
void LCD_str(char *str) {
    while (*str) //0x00まで繰り返し
        LCD_dat(*str++); //１文字表示
}

//１文字表示
void LCD_dat(char chr) {
    data[0] = 0x40;
    data[1] = chr;

    //I2C送信
    bhi2c = DRV_I2C_Transmit(hi2c, ADR, data, 2, NULL);
    while (DRV_I2C_TransferStatusGet(hi2c, bhi2c) != DRV_I2C_BUFFER_EVENT_COMPLETE); 
    
    BSP_DelayUs(60); // 60usec

}

//-------- １６進文字変換表示 ----------------
void LCD_hex(char c) {
    const char hexch[] = "0123456789ABCDEF";
    LCD_dat(hexch[c >> 4]); //上位4bit表示
    LCD_dat(hexch[c & 0xF]); //下位4bit表示
}

//--------３桁 １０進文字表示 ----------------
void LCD_dec(int i) {
    const char decch[] = "0123456789 ";
    char n[3];

    n[2] = i / 100;
    n[1] = (i % 100) / 10;
    n[0] = i % 10;

    if (n[2] == 0){
        n[2] = 10;//100の桁は０ならスペース
        if (n[1] == 0){
            n[1] = 10;//100の桁０で10の桁０ならスペース
        }
    }
    
    LCD_dat(decch[n[2]]);
    LCD_dat(decch[n[1]]);
    LCD_dat(decch[n[0]]);


}
//-------- カーソル位置指定 --------------------------------------

void LCD_posyx(char ypos, char xpos) {
    unsigned char pcode;
    switch (ypos & 0x03) { // 縦位置を取得
        case 0: pcode = 0x80;
            break; // 1行目
        case 1: pcode = 0xC0;
            break; // 2行目
        case 2: pcode = 0x94;
            break; // 3行目
        case 3: pcode = 0xD4;
            break; // 4行目
    }
    LCD_cmd(pcode += xpos); // 横位置を加える
}
/*******************************************************************************
 End of File
 */

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

//2022_0612 lcd.c

#include "system/common/sys_common.h"

#include "app.h"

#include "system_definitions.h"

#define ADR 0x7C

void LCD_cmd(char);

void LCD_int(void);

void LCD_str(char *);

void LCD_dat(char);

void LCD_hex(char);

void LCD_posyx(char, char);

void BSP_DelayMs(unsigned short);

void BSP_DelayUs(unsigned short);

uint8_t data[5];

//遅延調整用関数（ｍｓ）

void BSP_DelayMs(unsigned short milliseconds) {

unsigned long time;

time = _CP0_GET_COUNT(); //Read Core Timer

time += (SYS_CLK_FREQ / 2 / 1000) * milliseconds; //calc the Stop Time

while ((long) (time - _CP0_GET_COUNT()) > 0) {

};

}

//遅延調整用関数（μｓ）

void BSP_DelayUs(unsigned short microseconds) {

unsigned long time;

time = _CP0_GET_COUNT(); //Read Core Timer

time += (SYS_CLK_FREQ / 2 / 1000000) * microseconds; //calc the Stop Time

while ((long) (time - _CP0_GET_COUNT()) > 0) {

};

}

void LCD_cmd(char cmd) {

data[0] = 0x80;

data[1] = cmd;

bhi2c = DRV_I2C_Transmit(hi2c, ADR, data, 2, NULL);//I2C送信

while (DRV_I2C_TransferStatusGet(hi2c, bhi2c) != DRV_I2C_BUFFER_EVENT_COMPLETE); /*I2C完了待ち*/

if (cmd & 0xFC) // LCDのコマンドにより待ち時間が違う

BSP_DelayUs(60); // 60usec

else

BSP_DelayMs(3); // 3msec

}

void LCD_int(void) {

BSP_DelayMs(100);

LCD_cmd(0x38);

LCD_cmd(0x39);

LCD_cmd(0x14);

LCD_cmd(0x73); //7A(forAQM1602)

LCD_cmd(0x56); //54(forAQM1602)

LCD_cmd(0x6C);

BSP_DelayMs(200);

LCD_cmd(0x0C); //Disp ON/OFF

LCD_cmd(0x01);// Clear Display

BSP_DelayUs(1100);

}

//文字列表示

void LCD_str(char *str) {

while (*str) //0x00まで繰り返し

LCD_dat(*str++); //１文字表示

}

//１文字表示

void LCD_dat(char chr) {

data[0] = 0x40;

data[1] = chr;

//I2C送信

bhi2c = DRV_I2C_Transmit(hi2c, ADR, data, 2, NULL);

while (DRV_I2C_TransferStatusGet(hi2c, bhi2c) != DRV_I2C_BUFFER_EVENT_COMPLETE);

BSP_DelayUs(60); // 60usec

}

//-------- １６進文字変換表示 ----------------

void LCD_hex(char c) {

const char hexch[] = "0123456789ABCDEF";

LCD_dat(hexch[c >> 4]); //上位4bit表示

LCD_dat(hexch[c & 0xF]); //下位4bit表示

}

//--------３桁１０進文字表示 ----------------

void LCD_dec(int i) {

const char decch[] = "0123456789 ";

char n[3];

n[2] = i / 100;

n[1] = (i % 100) / 10;

n[0] = i % 10;

if (n[2] == 0){

n[2] = 10;//100の桁は０ならスペース

if (n[1] == 0){

n[1] = 10;//100の桁０で10の桁０ならスペース

}

LCD_dat(decch[n[2]]);

LCD_dat(decch[n[1]]);

LCD_dat(decch[n[0]]);

}

//-------- カーソル位置指定 --------------------------------------

void LCD_posyx(char ypos, char xpos) {

unsigned char pcode;

switch (ypos & 0x03) { // 縦位置を取得

case 0: pcode = 0x80;

break; // 1行目

case 1: pcode = 0xC0;

break; // 2行目

case 2: pcode = 0x94;

break; // 3行目

case 3: pcode = 0xD4;

break; // 4行目

}

LCD_cmd(pcode += xpos); // 横位置を加える

}

/*******************************************************************************

End of File

・Souse Files – appに “timer_int.c” を追加

timer_int.c

//
//2022_0903
//
#include "system/common/sys_common.h"
#include "app.h"
#include "system_definitions.h"


void kukan_ON(unsigned char, unsigned char);
void section_change_monitor(unsigned char, unsigned char); //区間変化監視
void next_section_on(unsigned char, unsigned char); //次区間ＯＮ
void read_generated_voltage(unsigned char, unsigned char);
void speed_cont(unsigned char);
void section_change(void);
void board_comm(unsigned char); //ボード間通信
void comm_data_set_tx(void); //通信データ設定TX
void comm_data_set_rx(void); //通信データ設定RX
void point_cont(void);
void yard_cont(void);
void set_on_section(unsigned char, unsigned char);
void set_on_next_section(unsigned char, unsigned char);
void timer2_int_func(char);
void PulseOffTimer_start(char);

void timer_int_func() {

    unsigned char rec_bit; //受信BIT用
    unsigned char send_flg; //送信PORT用

    rec_bit = _RB11;

#if ROSEN_NUM==0
    _RB10 = 0; //ext_int 同期パルス(master board))

#else
    //_RB14 = 1; //OSC
    DRV_TMR0_CounterValueSet(96);
#endif


    //通信用comm_counterはインタラプトを0-0x3ffでカウントします。
    if (++comm_counter > 0x3ff) {
        comm_counter = 0;
    } else {
#if ROSEN_NUM==0
        _RB10 = 1;
        _RB10 = 1;
#endif
    }



#if ROSEN_NUM!=0
    //子ボードは同期パルス幅が大きいときcomm_counterをリセット
    if (_RB10 == 0) {
        comm_counter = 0;
        _RB14 = 1; //OSC
    }
#endif
    //int_counterはcomm_counterの下位9bitの0-0x1ffでカウントします。
    int_counter = comm_counter & 0x1ff;

    _TRISB11 = 1;

    //osc_trg
#if ROSEN_NUM==0
    if (comm_counter == osc_trg.INT)_RB14 = 1;
#endif

    TRISB |= 0x10ff; //0x10ff

    //timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

    unsigned int t1 = 0x62;
    sp_w1 = speed_pw[0];
    sp_w2 = speed_pw[1];

    if (sp_w1 > t1) sp_w1 -= t1;
    if (sp_w2 > t1) sp_w2 -= t1;


    if (!same_dir_mode) {
        if (int_counter >= 0x10 && int_counter < 0x100) {
            //正転側区間ＯＮ
            kukan_ON(0, 0);
            kukan_ON(1, 0);
        } else if (int_counter >= 0x110 && int_counter <= 0x1ff) {
            //逆転側PWM ON
            kukan_ON(0, 1);
            kukan_ON(1, 1);
        }
    } else {
        //-----同方向-----
        if (int_counter >= 0x10 && int_counter < 0x100) {
            //
            kukan_ON(0, same_dir);
            kukan_ON(1, same_dir);
        } else {
            if (int_counter >= 0x110) {
                if (int_counter <= (ext_pwr[0] + 0x10f)) {
                    kukan_ON(0, same_dir);
                }
                if (int_counter <= (ext_pwr[1] + 0x10f)) {
                    kukan_ON(1, same_dir);
                }
            }
        }
    }




    switch (int_counter) {
        case 0:
            section_change();

            if (!same_dir_mode) {
                set_on_section(0, 0);
                set_on_section(1, 0);
            } else {
                set_on_section(0, same_dir);
                set_on_section(1, same_dir);
            }

            break;

        case 2:
            speed_cont(0);
            speed_cont(1);
            break;

        case 0x12:
            //インタラプトカウンタが0x2のときA相の区間変化監視(B相は0x102のとき)
            if (!same_dir_mode) {
                section_change_monitor(0, 0);
            } else {
                section_change_monitor(0, same_dir);
            }
            break;
        case 0x13:
            //インタラプトカウンタが0x2のときA相の区間変化監視(B相は0x102のとき)
            if (!same_dir_mode) {
                section_change_monitor(1, 0);
            } else {
                section_change_monitor(1, same_dir);
            }

            break;

        case 0x15:
            //インタラプトカウンタが3のときNEXT区間パルスON(B相は0x103のとき)
            //区間変化確認後に次区間もON
            if (!same_dir_mode) {
                set_on_next_section(0, 0);
                set_on_next_section(1, 0);
            } else {
                set_on_next_section(0, same_dir);
                set_on_next_section(1, same_dir);
            }

            break;

        case 0x100:
            //インタラプトカウンタが0x100のときB相のspeedパルスON
            if (!same_dir_mode) {
                set_on_section(0, 1);
                set_on_section(1, 1);
            }
            break;

        case 0x112:
            //区間変化監視
            if (!same_dir_mode) {
                section_change_monitor(0, 1);
            }
            break;
        case 0x113:
            //区間変化監視
            if (!same_dir_mode) {
                section_change_monitor(1, 1);
            }
            break;

        case 0x115:
            //区間変化確認後に次区間もON
            if (!same_dir_mode) {
                set_on_next_section(0, 1);
                set_on_next_section(1, 1);
            }
            break;

    }
    if (!same_dir_mode) {
        if (int_counter >= 0x8 && int_counter < 0xF) {
            read_generated_voltage(int_counter & 1, 1);
        }
        if (int_counter >= 0x108 && int_counter < 0x10F) {
            read_generated_voltage(int_counter & 1, 0);
        }
    } else {//same_dir_mode
        if (int_counter >= 0x8 && int_counter < 0xF) {
            read_generated_voltage(int_counter & 1, 1);
        }
        if (int_counter >= 0x1e8 && int_counter < 0x1eF) {
            read_generated_voltage(int_counter & 1, 0);
        }
    }



    switch (comm_counter) {
#if ROSEN_NUM == 0//-----ポイント yard 制御----------       
        case 0x3:
            point_cont();
            break;
        case 0x5:
            yard_cont();
            break;
#endif
        case 0x4:
            comm_data_set_tx();
            break;
        case 0x6:
            comm_data_set_rx();
            break;

    }


    //ボード間の通信
    board_comm(rec_bit);


#if ROSEN_NUM==0
    //幅広同期パルスOFF
    if (comm_counter == 0) {
        _RB10 = 1;
        _RB10 = 1;
    }

#endif


    _RB14 = 0; //OSC

    section1 = kukan[0];
    section2 = kukan[1];

    timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);
    int w1 = sp_w1 - timer_value.INT;
    int w2 = sp_w2 - timer_value.INT;

    debug2.INT = w1;


    both_off = 0;

#define delay1 200 //このTimer0インタラプトが終わるまで待機する時間

    if (w1 > delay1 && w2 > delay1) {
        if (abs(w2 - w1) < 250) {
            //2列車のSpeedPulse幅の差がないときはどちらか早いほうのTimerでPulseOFF
            both_off = 1;
            if (w1 < w2) {
                PulseOffTimer_start(0);
            } else {
                PulseOffTimer_start(1);
            }
        } else {
            PulseOffTimer_start(0);
            PulseOffTimer_start(1);
        }
    } else {
        if (w1 > delay1) {
            PulseOffTimer_start(0);
        } else {
            timer2_int_func(0); //speed pulse短いときはここでOFF
            debug1.INT = 0xff00;
        }

        if (w2 > delay1) {
            PulseOffTimer_start(1);
        } else {
            timer2_int_func(1); //speed pulse短いときはここでOFF
            //debug1.INT = 0xff00;
        }
    }


}

//speed pulse off timer
void PulseOffTimer_start(char s) {
    int w;

    if (s == 0) {
        w = sp_w1 - TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);
        PLIB_TMR_Period16BitSet(TMR_ID_2, w);
        DRV_TMR1_Start(); //PULSE OFF TimerStart
        int_count1.INT++;
    } else {
        w = sp_w2 - TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);
        PLIB_TMR_Period16BitSet(TMR_ID_4, w);
        DRV_TMR2_Start(); //PULSE OFF TimerStart
        int_count2.INT++;
    }
}

void set_on_section(unsigned char sou, unsigned char dir) {

    if (train_sou[sou]) {
        if (train_sou[sou]->NOW.BIT.DIR == dir) {
            kukan[sou] = 0; //kukan clr

            if (train_sou[sou]->STATUS.BIT.SP_MANU == 1)
                speed_pw[sou] = train_sou[sou]->speed * SPEED_MAX / 256; //manual speed
            else
                speed_pw[sou] = train_sou[sou]->speed_cont.INT; //auto speed

            //区間メモリに現・前位置の区間を設定し区間ON
            if (train_sou[sou]->NOW.BIT.ROSEN == ROSEN_NUM) {
                if (speed_pw[sou] > 0)
                    kukan[sou] = EnableBit[train_sou[sou]->NOW.BIT.KUKAN];
                kanshi_now[sou] = train_sou[sou]->NOW.BIT.KUKAN;
            }
            if (train_sou[sou]->BEFORE.BIT.ROSEN == ROSEN_NUM) {
                if (speed_pw[sou] > 0)
                    kukan[sou] |= EnableBit[train_sou[sou]->BEFORE.BIT.KUKAN];
                kanshi_before[sou] = train_sou[sou]->BEFORE.BIT.KUKAN;
            }

        }
    }

}

void set_on_next_section(unsigned char sou, unsigned char dir) {

    if (train_sou[sou]) {
        if (train_sou[sou]->STATUS.BIT.SAFE) {
            //安全でないときは次区間に他の列車がかかっているのでONしない。
            if (train_sou[sou]->NOW.BIT.DIR == dir) {
                if (train_sou[sou]->NEXT.BIT.ROSEN == ROSEN_NUM) {
                    kukan[sou] |= EnableBit[train_sou[sou]->NEXT.BIT.KUKAN];
                }
            }
        }
    }
}


//区間ON用

void kukan_ON(unsigned char sou, unsigned char d) {
    if (train_sou[sou]) {
        if (train_sou[sou]->NOW.BIT.DIR == d) {
            // d=0:正回転, 1:負回転
            if (d == 0) {
                LATB |= kukan[sou];
                _LATB12 = 0; //Port RB12は共通側
            } else {
                LATB &= ~kukan[sou];
                _LATB12 = 1;
            }

            TRISB &= ~kukan[sou];
            _TRISB12 = 0;
        }
    }

}

void section_change_monitor(unsigned char sou, unsigned char dir) {
    static char sum_count;
    static int gnd_sum;

    if (train_sou[sou]) {
        if (train_sou[sou^1]) //相手変更中は変更しない
            if (train_sou[sou^1]->henka) return;

        if (train_sou[sou]->NOW.BIT.DIR == dir) {
            char chg_enable = 0;
            if (train_sou[sou^0x1]) {
                //向き合いの時区間変更許可
                if (train_sou[sou]->NOW.BIT.DIR != train_sou[sou^0x1]->NOW.BIT.DIR)
                    chg_enable = 1;
            }

            if (train_sou[sou]->STATUS.BIT.SAFE || chg_enable)
                if (!train_sou[sou]->henka) {
                    if (train_sou[sou]->NEXT.BIT.ROSEN == ROSEN_NUM) {
                        //次位置区間の監視
                        kanshi.BIT.KUKAN = train_sou[sou]->NEXT.BIT.KUKAN;
                        LATA &= 0xC3;
                        LATA |= kanshi.BYTE;

                        //ADC読み込み
                        BSP_DelayUs(1);
                        //_RB14 = 1;
                        PLIB_ADC_SamplingStart(ADC_ID_1);
                        while (!PLIB_ADC_ConversionHasCompleted(ADC_ID_1));
                        adc_ret.INT = PLIB_ADC_ResultGetByIndex(ADC_ID_1, 0);
                        //_RB14 = 0;

                        if (train_sou[sou]->NOW.BIT.DIR == 0) {
                            //正方向のとき
                            if (adc_ret.INT >= 0x280) {
                                train_sou[sou]->henka = 0x80; //区間変化

                            }
                            //if (sou == 0)debug1.INT = adc_ret.INT;
                            //else debug2.INT = adc_ret.INT;
                        } else {
                            //逆方向のとき
                            if (adc_ret.INT < 0x180) {
                                train_sou[sou]->henka = 0x80; //区間変化

                            }
                            //if (sou == 0)debug1.INT = adc_ret.INT;
                            //else debug2.INT = adc_ret.INT;

                        }

                        //区間変化でないときGND値とする。
                        //                        if (!train_sou[sou]->henka) {
                        //                            gnd_adc = adc_ret.INT;
                        //
                        //                            //区間変更なしのときのADC値をGND Levelにします。
                        //                            //16回たして4bit右シフトで平均をとります。
                        //                            gnd_sum += adc_ret.INT;
                        //                            if (sum_count++ == 15) {
                        //                                gnd_level.INT = gnd_sum >> 4;
                        //                                sum_count = 0;
                        //                                gnd_sum = 0;
                        //                            }
                        //
                        //                        }

                    }
                }
        }
    }

}

void next_section_on(unsigned char sou, unsigned char dir) {
    //次区間をON
    if (train_sou[sou]) {
        if (train_sou[sou]->NOW.BIT.DIR == dir) {
            if (train_sou[sou]->STATUS.BIT.SAFE) {
                //安全でないときは次区間に他の列車がかかっているのでONしない。
                if (train_sou[sou]->NEXT.BIT.ROSEN == ROSEN_NUM) {
                    kukan[sou] |= EnableBit[train_sou[sou]->NEXT.BIT.KUKAN];
                    //kukan_ON(kukan[sou], train_sou[sou]->NOW.BIT.DIR);
                }
            }
        }
    }
}

void read_generated_voltage(unsigned char n, unsigned char sou) {
    static unsigned char count[2], p[2], count_B[2];
    static int speed_buf[2][32]; //16
    static int read_speed[2];
    static int speed_sou[2]; //相手のスピード

    char m;

    if (train_sou[sou]) {

        char sou_b = 0;
        if (sou == 0) sou_b = 1;

        //現位置と前位置を交互に読み込み
        if (n == 0) {//n == 0
            kanshi.BIT.KUKAN = kanshi_now[sou];
            //kanshi.BIT.KUKAN = train_sou[sou]->NOW.BIT.KUKAN;
        } else {
            kanshi.BIT.KUKAN = kanshi_before[sou];
            //kanshi.BIT.KUKAN = train_sou[sou]->BEFORE.BIT.KUKAN;
        }

        //        LATA &= 0xC3;
        //        LATA |= kanshi.BYTE;
        PORTA = kanshi.BYTE;

        //BSP_DelayUs(1);

        //ADC読み込み
        PLIB_ADC_SamplingStart(ADC_ID_1);
        while (!PLIB_ADC_ConversionHasCompleted(ADC_ID_1));
        adc_ret.INT = PLIB_ADC_ResultGetByIndex(ADC_ID_1, 0);

        //ADC値からGND値を引いて絶対値をとります。
        adc_ret.INT = adc_ret.INT - gnd_level.INT;

        if (adc_ret.INT < 0)
            adc_ret.INT = -adc_ret.INT;

        //8回のピーク値をスピードデータにします。
        //        if (count[sou]++ == 7) {
        //            read_speed[sou] = adc_ret.INT;
        //            count[sou] = 0;
        //        } else if (adc_ret.INT > read_speed[sou]) {
        //            read_speed[sou] = adc_ret.INT;
        //            return; //ここで終了
        //        }


        //8回のピーク値をスピードデータにします。
        if (adc_ret.INT > read_speed[sou]) {
            read_speed[sou] = adc_ret.INT;
        }

        speed_sou[sou] = read_speed[sou];

        //        p[sou]++;
        //        if (p[sou] == 16) p[sou] = 0;
        //
        //        speed_buf[sou][p[sou]] = read_speed[sou]; //0xf
        speed_buf[sou][++p[sou] & 0xf] = read_speed[sou]; //0xf

        //peek reset
        if (++count[sou] == 8) {
            read_speed[sou] = adc_ret.INT;
            count[sou] = 0;
        }


        //移動平均
        //char m;
        unsigned long avr = 0;

        for (m = 0; m < 16; m++) {//16
            avr += speed_buf[sou][m];
        }

        avr >>= 4; //4
        //avr = read_speed[sou];

        //読み取り電圧補正
        //        if (volt_kb.INT < 0x100 || volt_kb.INT > 0x280)
        //            volt_kb.INT = 0x150;
        //
        //        avr = avr * volt_kb.INT;
        //        avr = avr / 0x100;

        //train_sou[sou]->speed_ret.INT = avr; //4


        if (count_B[sou]++ == 15) {
            count_B[sou] = 0;

            if (avr < train_sou[sou]->speed_ret.INT) {
                train_sou[sou]->speed_ret.INT--;
            } else if (avr > train_sou[sou]->speed_ret.INT)
                train_sou[sou]->speed_ret.INT++;
        }


        if (train_sou[sou]->NOW.BIT.ROSEN == ROSEN_NUM) {
            if (train_sou[sou]->NOW.BIT.ROSEN != train_sou[sou]->BEFORE.BIT.ROSEN) {
                if (train_sou[sou]->speed_ret_rx.INT > train_sou[sou]->speed_ret.INT) {
                    train_sou[sou]->speed_ret.INT = train_sou[sou]->speed_ret_rx.INT;
                }
            }
        }


    }
}

void speed_cont(unsigned char sou) {
    int err; //スピードのエラー
    //    int err_abs; //err絶対値

    int d; //エラー補正値

    static char count[2];
    static char count_avr[2];

    if (!train_sou[sou])return;

    // スピード設定値と実際スピードの比較
    err = train_sou[sou]->speed - train_sou[sou]->speed_ret.INT;

    err_buff[sou][count_avr[sou]++ & 0xF] = err;

    //---error avrage---
    int err_sum = 0;
    char c;
    for (c = 0; c < 16; c++) {
        err_sum += err_buff[sou][c];
    }
    err_avr[sou].INT = err_sum / 16;

    //    err_abs = err_avr[sou].INT;
    //    if (err_abs < 0)err_abs = -err_abs;

    //--test--
    //d = (err * err_avr[sou].INT) / 0x80;
    //d = err_avr[sou].INT / 0x10;
    d = err_avr[sou].INT / 4; // /10

    int d_max = 0x50; //+補正最大値
    //int d_max_m = 0x100; //-補正最大値
    char cont_t = 10; //制御間隔

    //動き出しを早く
    if (train_sou[sou]->speed_ret.INT < 10) {
        d_max = 0x100;
        cont_t = 2;
    }

    //    if (d > d_max)d = d_max;
    //    else if (d < -d_max_m)d = -d_max_m;


    //スピード設定が０のとき補正値が負でない場合
    //完全に停止させるため補正値を-1にします

#define d_zero -20
    if (train_sou[sou]->speed == 0) {
        cont_t = 2; //減速早く 2
        if (d > d_zero)//-3
            d = d_zero; //-0x3
    } else {
        //if (err_avr[sou].INT < train_sou[sou]->err_th)return;
        //if (err_abs < train_sou[sou]->err_th)return;
    }


    //if (d < 0) cont_t = 20; //減速は早く


    //スピードコントロール値をエラー補正値で補正
    if (++count[sou] > cont_t) {//10
        count[sou] = 0;
        train_sou[sou]->speed_cont.INT += d;
    } else {
        return;
    }


    //結果が負にならないようにする
    if (train_sou[sou]->speed_cont.INT < 0)
        train_sou[sou]->speed_cont.INT = 0;

    //接触不良時の制限
    if (train_sou[sou]->speed_ret.INT < 0x4) {
        int contact_fail = SPEED_MAX * 10 / 10; //max/2
        if (train_sou[sou]->speed_cont.INT > contact_fail)
            train_sou[sou]->speed_cont.INT = contact_fail;
    }

    //Speedの最大値を制限
    if (train_sou[sou]->speed_cont.INT > SPEED_MAX) {
        train_sou[sou]->speed_cont.INT = SPEED_MAX;
    }

    //extra_power
    if (train_sou[sou]->speed_cont.INT > SPEED_MAX - 0x20) {
        if (ext_pwr[sou] < 0xc0) {
            if ((count_avr[sou] & 0xf) == 0) ext_pwr[sou]++;
        }
    } else {
        if (ext_pwr[sou] > 0) {
            ext_pwr[sou]--;
        }
    }

    //ext_pwr[sou] = 0; //test

}

void section_change() {
    char n;
    // if (chg_disable) return;

    for (n = 0; n < TR_COUNT; n++) {
        if (train[n].STATUS.BIT.CHG == 1) {
            //受信データに置き換え
            train[n].BEFORE.BYTE = train[n].REC_BEFORE;
            train[n].NOW.BYTE = train[n].REC_NOW;
            train[n].NEXT.BYTE = train[n].REC_NEXT;

            if (cont_train[0] == n) {
                cont_train[0] = 0xff;
                train_sou[0] = NULL;
            }
            if (cont_train[1] == n) {
                cont_train[1] = 0xff;
                train_sou[1] = NULL;
            }

            if ((train[n].NOW.BIT.ROSEN == ROSEN_NUM)
                    || (train[n].NEXT.BIT.ROSEN == ROSEN_NUM)
                    || (train[n].BEFORE.BIT.ROSEN == ROSEN_NUM)) {
                //各相の列車登録
                cont_train[train[n].NOW.BIT.SOU] = n;
                train_sou[train[n].NOW.BIT.SOU] = &train[n];
            } else {
                train[n].speed_cont.INT = 0;
            }

            train[n].henka = 0;
            train[n].STATUS.BIT.CHG = 0;

        }
    }


    //kukan clr
    kukan[0] = 0;
    kukan[1] = 0;


    //check same dir
    if (train_sou[0] && train_sou[1]) {//両相ともON?
        if (train_sou[0]->NOW.BIT.DIR == train_sou[1]->NOW.BIT.DIR) {//same dir?
            if (same_dir_mode < 0x80 && inc_interval++ > 50) {
                same_dir_mode++;
                inc_interval = 0;
            }
            same_dir = train_sou[0]->NOW.BIT.DIR; //set dir
        } else {
            same_dir_mode = 0;
            inc_interval = 0;
        }
    } else {
        //one side only
        if (same_dir_mode < 0x80 && inc_interval++ > 50) {
            same_dir_mode++;
            inc_interval = 0;
        }
        if (train_sou[0]) {
            same_dir = train_sou[0]->NOW.BIT.DIR;
        }
        if (train_sou[1]) {
            same_dir = train_sou[1]->NOW.BIT.DIR;
        }
    }

}

void board_comm(unsigned char rec_bit) {
    unsigned char bit_p;
    unsigned int data_p;

    data_p = (comm_counter - 1) & 0x3ff;
    bit_p = EnableBit[data_p & 7]; //bit位置set
    data_p >>= 3;
    board_num = data_p;
    board_num >>= 4;

#if ROSEN_NUM == 0
    //親ボードのみポイントなどのボードに送信
    if (!(board_num == ROSEN_NUM || board_num == 6)) {
#else
    if (!(board_num == ROSEN_NUM)) {
#endif
        //データ受信
        _TRISB11 = 1;

        if (rec_bit)
            receive_data |= bit_p;
        else
            receive_data &= ~bit_p;

        if (bit_p == 0x80) {

            comm_data[data_p] = receive_data;
        }

    }


    //ボード間データ通信
    data_p = comm_counter & 0x3ff;
    bit_p = EnableBit[data_p & 7]; //bit位置set
    data_p >>= 3;
    board_num = data_p;
    board_num >>= 4;

#if ROSEN_NUM == 0
    //親ボードのみポイントなどのボードに送信
    if (board_num == ROSEN_NUM || board_num == 6) {
#else
    if (board_num == ROSEN_NUM) {
#endif
        //データ送信
        _TRISB11 = 0;

        send_data = comm_data[data_p];

        //送信PORTデータセット
        if (send_data & bit_p)
            _RB11 = 1;
        else
            _RB11 = 0;

    }
}

void comm_data_set_tx() {
    unsigned char n;
    unsigned int data_p;

    //comm_data 送信データSET
    data_p = ROSEN_NUM << 4;
    //A相
    n = cont_train[0];
    if (n != 0xff) {
        comm_data[data_p] = n + 0xA0;
        comm_data[data_p + 1] = train[n].speed_ret.BYTE.H; //speed_ret_tx
        comm_data[data_p + 2] = train[n].speed_ret.BYTE.L;
        comm_data[data_p + 3] = train[n].henka;
        comm_data[data_p + 4] = train[n].speed_cont.BYTE.H;
        comm_data[data_p + 5] = train[n].speed_cont.BYTE.L;

        comm_data[data_p + 6] = train[n].NOW.BYTE;

        comm_data[data_p + 7] = ext_pwr[0]; //same_dir_mode

    } else
        comm_data[data_p] = 0xFF;


    //B相
    n = cont_train[1];
    data_p += 0x8;

    if (n != 0xff) {
        comm_data[data_p] = n + 0xA0;
        comm_data[data_p + 1] = train[n].speed_ret.BYTE.H; //speed_ret_tx
        comm_data[data_p + 2] = train[n].speed_ret.BYTE.L;
        comm_data[data_p + 3] = train[n].henka;
        comm_data[data_p + 4] = train[n].speed_cont.BYTE.H;
        comm_data[data_p + 5] = train[n].speed_cont.BYTE.L;

        comm_data[data_p + 6] = train[n].NOW.BYTE;
    } else
        comm_data[data_p] = 0xFF;

}

void comm_data_set_rx() {
    //受信データSET
    unsigned char n;
    unsigned int data_p;

    for (board_num = 0; board_num < BOARD_COUNT; board_num++) {
        if (board_num != ROSEN_NUM) {
            //自ボード以外受信
            data_p = board_num << 4;
            //A相
            n = comm_data[data_p];
            if ((n & 0xF0) == 0xA0) {
                n &= 0xF;

                train[n].speed_ret_rx.BYTE.H = comm_data[data_p + 1];
                train[n].speed_ret_rx.BYTE.L = comm_data[data_p + 2];

                if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {
                    if (train[n].NOW.BIT.ROSEN == train[n].BEFORE.BIT.ROSEN)
                        //現位置および前位置が他路線のとき実スピード受信
                        train[n].speed_ret.INT = train[n].speed_ret_rx.INT;
                }

                if (ROSEN_NUM == 0)//Masterボードのみ区間変化受信
                    if (train[n].NEXT.BIT.ROSEN != 0) {
                        //NextがMasterボード以外のとき受信
                        if (train[n].NEXT.BIT.ROSEN == board_num)//次区間のボードの区間変化を受信
                            train[n].henka = comm_data[data_p + 3];
                    }


                train[n].speed_rx.BYTE.H = comm_data[data_p + 4];
                train[n].speed_rx.BYTE.L = comm_data[data_p + 5];

                if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {
                    if (train[n].NEXT.BIT.ROSEN == ROSEN_NUM)
                        //ポイント切り替え時次区間でspeed_cont渡し
                        train[n].speed_cont.INT = train[n].speed_rx.INT;
                }


            }
            //B相
            data_p += 0x8;
            n = comm_data[data_p];
            if ((n & 0xF0) == 0xA0) {
                n &= 0xF;

                train[n].speed_ret_rx.BYTE.H = comm_data[data_p + 1];
                train[n].speed_ret_rx.BYTE.L = comm_data[data_p + 2];

                if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {
                    if (train[n].NOW.BIT.ROSEN == train[n].BEFORE.BIT.ROSEN)
                        //現位置および前位置が他路線のとき実スピード受信
                        train[n].speed_ret.INT = train[n].speed_ret_rx.INT;
                }

                if (ROSEN_NUM == 0)//Masterボードのみ区間変化受信
                    if (train[n].NEXT.BIT.ROSEN != 0) {
                        //NextがMasterボード以外のとき受信
                        if (train[n].NEXT.BIT.ROSEN == board_num)//次区間のボードの区間変化を受信
                            train[n].henka = comm_data[data_p + 3];
                    }

                train[n].speed_rx.BYTE.H = comm_data[data_p + 4];
                train[n].speed_rx.BYTE.L = comm_data[data_p + 5];

                if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {
                    if (train[n].NEXT.BIT.ROSEN == ROSEN_NUM)
                        //ポイント切り替え時次区間でspeed_cont渡し
                        train[n].speed_cont.INT = train[n].speed_rx.INT;
                }


            }
        }
    }


#if ROSEN_NUM == 0
    //point_request
    if (point_req) {
        if (!comm_data[0x70]) {
            //ready
            comm_data[0x60] = point_req; //point_data
        } else
            //busy
            if (comm_data[0x60]) {
            //リクエストクリア
            point_req = 0;
            comm_data[0x60] = 0;
        }
    }

    //yardt_request
    if (yard_req) {
        if (!comm_data[0x71]) {
            //ready
            comm_data[0x61] = yard_req; //point_data
        } else
            //busy
            if (comm_data[0x61]) {
            //リクエストクリア
            yard_req = 0;
            comm_data[0x61] = 0;
        }
    }
#endif

}

//ポイント制御

void point_cont() {
    unsigned char n;

    if (!point_req) {
        for (n = 0; n < TR_COUNT; n++) {
            if ((train[n].point & 0x80) != 0) {
                point_req = train[n].point;
                train[n].point = 0;
                break;
            }
        }
    }
}

//ヤード制御

void yard_cont() {
    unsigned char n;

    if (!yard_req) {
        for (n = 0; n < TR_COUNT; n++) {
            if ((train[n].yard & 0x80) != 0) {
                yard_req = train[n].yard;
                train[n].yard = 0;
                break;
            }
        }
    }
}

//pulse off用インタラプトFunction
void timer2_int_func(char s) {

    if (s == 0) {//TM1
        if (section1) TRISB |= section1;
        DRV_TMR1_Stop();

        if (both_off) {//2列車のSpeedPulse幅の差がないときはどちらか早いほうのTimerでPulseOFF
            do {
                timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);
            } while (timer_value.INT < sp_w2);
            if (section2) TRISB |= section2;
        }

    } else {//TM2
        if (section2) TRISB |= section2;
        DRV_TMR2_Stop();

        if (both_off) {//2列車のSpeedPulse幅の差がないときはどちらか早いほうのTimerでPulseOFF
            do {
                timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);
            } while (timer_value.INT < sp_w1);
            if (section1) TRISB |= section1;
        }
    }
   
}

/* *****************************************************************************
 End of File
 */

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

256

257

258

259

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

275

276

277

278

279

280

281

282

283

284

285

286

287

288

289

290

291

292

293

294

295

296

297

298

299

300

301

302

303

304

305

306

307

308

309

310

311

312

313

314

315

316

317

318

319

320

321

322

323

324

325

326

327

328

329

330

331

332

333

334

335

336

337

338

339

340

341

342

343

344

345

346

347

348

349

350

351

352

353

354

355

356

357

358

359

360

361

362

363

364

365

366

367

368

369

370

371

372

373

374

375

376

377

378

379

380

381

382

383

384

385

386

387

388

389

390

391

392

393

394

395

396

397

398

399

400

401

402

403

404

405

406

407

408

409

410

411

412

413

414

415

416

417

418

419

420

421

422

423

424

425

426

427

428

429

430

431

432

433

434

435

436

437

438

439

440

441

442

443

444

445

446

447

448

449

450

451

452

453

454

455

456

457

458

459

460

461

462

463

464

465

466

467

468

469

470

471

472

473

474

475

476

477

478

479

480

481

482

483

484

485

486

487

488

489

490

491

492

493

494

495

496

497

498

499

500

501

502

503

504

505

506

507

508

509

510

511

512

513

514

515

516

517

518

519

520

521

522

523

524

525

526

527

528

529

530

531

532

533

534

535

536

537

538

539

540

541

542

543

544

545

546

547

548

549

550

551

552

553

554

555

556

557

558

559

560

561

562

563

564

565

566

567

568

569

570

571

572

573

574

575

576

577

578

579

580

581

582

583

584

585

586

587

588

589

590

591

592

593

594

595

596

597

598

599

600

601

602

603

604

605

606

607

608

609

610

611

612

613

614

615

616

617

618

619

620

621

622

623

624

625

626

627

628

629

630

631

632

633

634

635

636

637

638

639

640

641

642

643

644

645

646

647

648

649

650

651

652

653

654

655

656

657

658

659

660

661

662

663

664

665

666

667

668

669

670

671

672

673

674

675

676

677

678

679

680

681

682

683

684

685

686

687

688

689

690

691

692

693

694

695

696

697

698

699

700

701

702

703

704

705

706

707

708

709

710

711

712

713

714

715

716

717

718

719

720

721

722

723

724

725

726

727

728

729

730

731

732

733

734

735

736

737

738

739

740

741

742

743

744

745

746

747

748

749

750

751

752

753

754

755

756

757

758

759

760

761

762

763

764

765

766

767

768

769

770

771

772

773

774

775

776

777

778

779

780

781

782

783

784

785

786

787

788

789

790

791

792

793

794

795

796

797

798

799

800

801

802

803

804

805

806

807

808

809

810

811

812

813

814

815

816

817

818

819

820

821

822

823

824

825

826

827

828

829

830

831

832

833

834

835

836

837

838

839

840

841

842

843

844

845

846

847

848

849

850

851

852

853

854

855

856

857

858

859

860

861

862

863

864

865

866

867

868

869

870

871

872

873

874

875

876

877

878

879

880

881

882

883

884

885

886

887

888

889

890

891

892

893

894

895

896

897

898

899

900

901

902

903

904

905

906

907

908

909

910

911

912

913

914

915

916

917

918

919

920

921

922

923

924

925

926

927

928

929

930

931

932

933

934

935

936

937

938

939

940

941

942

943

944

945

946

947

948

949

950

951

952

953

954

955

956

957

958

959

960

961

962

963

964

965

966

967

968

969

970

971

972

973

974

975

976

977

978

979

980

981

982

983

984

985

986

987

988

989

990

991

992

993

994

995

996

997

998

999

1000

1001

1002

1003

1004

1005

1006

1007

1008

1009

1010

1011

1012

1013

1014

1015

1016

1017

1018

1019

1020

//2022_0903

#include "system/common/sys_common.h"

#include "app.h"

#include "system_definitions.h"

void kukan_ON(unsigned char, unsigned char);

void section_change_monitor(unsigned char, unsigned char); //区間変化監視

void next_section_on(unsigned char, unsigned char); //次区間ＯＮ

void read_generated_voltage(unsigned char, unsigned char);

void speed_cont(unsigned char);

void section_change(void);

void board_comm(unsigned char); //ボード間通信

void comm_data_set_tx(void); //通信データ設定TX

void comm_data_set_rx(void); //通信データ設定RX

void point_cont(void);

void yard_cont(void);

void set_on_section(unsigned char, unsigned char);

void set_on_next_section(unsigned char, unsigned char);

void timer2_int_func(char);

void PulseOffTimer_start(char);

void timer_int_func() {

unsigned char rec_bit; //受信BIT用

unsigned char send_flg; //送信PORT用

rec_bit = _RB11;

#if ROSEN_NUM==0

_RB10 = 0; //ext_int 同期パルス(master board))

#else

//_RB14 = 1; //OSC

DRV_TMR0_CounterValueSet(96);

#endif

//通信用comm_counterはインタラプトを0-0x3ffでカウントします。

if (++comm_counter > 0x3ff) {

comm_counter = 0;

} else {

#if ROSEN_NUM==0

_RB10 = 1;

#endif

}

#if ROSEN_NUM!=0

//子ボードは同期パルス幅が大きいときcomm_counterをリセット

if (_RB10 == 0) {

comm_counter = 0;

_RB14 = 1; //OSC

}

#endif

//int_counterはcomm_counterの下位9bitの0-0x1ffでカウントします。

int_counter = comm_counter & 0x1ff;

_TRISB11 = 1;

//osc_trg

#if ROSEN_NUM==0

if (comm_counter == osc_trg.INT)_RB14 = 1;

#endif

TRISB |= 0x10ff; //0x10ff

//timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

unsigned int t1 = 0x62;

sp_w1 = speed_pw[0];

sp_w2 = speed_pw[1];

if (sp_w1 > t1) sp_w1 -= t1;

if (sp_w2 > t1) sp_w2 -= t1;

if (!same_dir_mode) {

if (int_counter >= 0x10 && int_counter < 0x100) {

//正転側区間ＯＮ

kukan_ON(0, 0);

kukan_ON(1, 0);

} else if (int_counter >= 0x110 && int_counter <= 0x1ff) {

//逆転側PWM ON

kukan_ON(0, 1);

kukan_ON(1, 1);

}

} else {

//-----同方向-----

if (int_counter >= 0x10 && int_counter < 0x100) {

kukan_ON(0, same_dir);

kukan_ON(1, same_dir);

} else {

if (int_counter >= 0x110) {

if (int_counter <= (ext_pwr[0] + 0x10f)) {

kukan_ON(0, same_dir);

}

if (int_counter <= (ext_pwr[1] + 0x10f)) {

kukan_ON(1, same_dir);

}

switch (int_counter) {

case 0:

section_change();

if (!same_dir_mode) {

set_on_section(0, 0);

set_on_section(1, 0);

} else {

set_on_section(0, same_dir);

set_on_section(1, same_dir);

}

break;

case 2:

speed_cont(0);

speed_cont(1);

break;

case 0x12:

//インタラプトカウンタが0x2のときA相の区間変化監視(B相は0x102のとき)

if (!same_dir_mode) {

section_change_monitor(0, 0);

} else {

section_change_monitor(0, same_dir);

}

break;

case 0x13:

//インタラプトカウンタが0x2のときA相の区間変化監視(B相は0x102のとき)

if (!same_dir_mode) {

section_change_monitor(1, 0);

} else {

section_change_monitor(1, same_dir);

}

break;

case 0x15:

//インタラプトカウンタが3のときNEXT区間パルスON(B相は0x103のとき)

//区間変化確認後に次区間もON

if (!same_dir_mode) {

set_on_next_section(0, 0);

set_on_next_section(1, 0);

} else {

set_on_next_section(0, same_dir);

set_on_next_section(1, same_dir);

}

break;

case 0x100:

//インタラプトカウンタが0x100のときB相のspeedパルスON

if (!same_dir_mode) {

set_on_section(0, 1);

set_on_section(1, 1);

}

break;

case 0x112:

//区間変化監視

if (!same_dir_mode) {

section_change_monitor(0, 1);

}

break;

case 0x113:

//区間変化監視

if (!same_dir_mode) {

section_change_monitor(1, 1);

}

break;

case 0x115:

//区間変化確認後に次区間もON

if (!same_dir_mode) {

set_on_next_section(0, 1);

set_on_next_section(1, 1);

}

break;

}

if (!same_dir_mode) {

if (int_counter >= 0x8 && int_counter < 0xF) {

read_generated_voltage(int_counter & 1, 1);

}

if (int_counter >= 0x108 && int_counter < 0x10F) {

read_generated_voltage(int_counter & 1, 0);

}

} else {//same_dir_mode

if (int_counter >= 0x8 && int_counter < 0xF) {

read_generated_voltage(int_counter & 1, 1);

}

if (int_counter >= 0x1e8 && int_counter < 0x1eF) {

read_generated_voltage(int_counter & 1, 0);

}

switch (comm_counter) {

#if ROSEN_NUM == 0//-----ポイント yard 制御----------

case 0x3:

point_cont();

break;

case 0x5:

yard_cont();

break;

#endif

case 0x4:

comm_data_set_tx();

break;

case 0x6:

comm_data_set_rx();

break;

}

//ボード間の通信

board_comm(rec_bit);

#if ROSEN_NUM==0

//幅広同期パルスOFF

if (comm_counter == 0) {

_RB10 = 1;

}

#endif

_RB14 = 0; //OSC

section1 = kukan[0];

section2 = kukan[1];

timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

int w1 = sp_w1 - timer_value.INT;

int w2 = sp_w2 - timer_value.INT;

debug2.INT = w1;

both_off = 0;

#define delay1 200 //このTimer0インタラプトが終わるまで待機する時間

if (w1 > delay1 && w2 > delay1) {

if (abs(w2 - w1) < 250) {

//2列車のSpeedPulse幅の差がないときはどちらか早いほうのTimerでPulseOFF

both_off = 1;

if (w1 < w2) {

PulseOffTimer_start(0);

} else {

PulseOffTimer_start(1);

}

} else {

PulseOffTimer_start(0);

PulseOffTimer_start(1);

}

} else {

if (w1 > delay1) {

PulseOffTimer_start(0);

} else {

timer2_int_func(0); //speed pulse短いときはここでOFF

debug1.INT = 0xff00;

}

if (w2 > delay1) {

PulseOffTimer_start(1);

} else {

timer2_int_func(1); //speed pulse短いときはここでOFF

//debug1.INT = 0xff00;

}

//speed pulse off timer

void PulseOffTimer_start(char s) {

int w;

if (s == 0) {

w = sp_w1 - TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

PLIB_TMR_Period16BitSet(TMR_ID_2, w);

DRV_TMR1_Start(); //PULSE OFF TimerStart

int_count1.INT++;

} else {

w = sp_w2 - TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

PLIB_TMR_Period16BitSet(TMR_ID_4, w);

DRV_TMR2_Start(); //PULSE OFF TimerStart

int_count2.INT++;

}

void set_on_section(unsigned char sou, unsigned char dir) {

if (train_sou[sou]) {

if (train_sou[sou]->NOW.BIT.DIR == dir) {

kukan[sou] = 0; //kukan clr

if (train_sou[sou]->STATUS.BIT.SP_MANU == 1)

speed_pw[sou] = train_sou[sou]->speed * SPEED_MAX / 256; //manual speed

else

speed_pw[sou] = train_sou[sou]->speed_cont.INT; //auto speed

//区間メモリに現・前位置の区間を設定し区間ON

if (train_sou[sou]->NOW.BIT.ROSEN == ROSEN_NUM) {

if (speed_pw[sou] > 0)

kukan[sou] = EnableBit[train_sou[sou]->NOW.BIT.KUKAN];

kanshi_now[sou] = train_sou[sou]->NOW.BIT.KUKAN;

}

if (train_sou[sou]->BEFORE.BIT.ROSEN == ROSEN_NUM) {

if (speed_pw[sou] > 0)

kukan[sou] |= EnableBit[train_sou[sou]->BEFORE.BIT.KUKAN];

kanshi_before[sou] = train_sou[sou]->BEFORE.BIT.KUKAN;

}

void set_on_next_section(unsigned char sou, unsigned char dir) {

if (train_sou[sou]) {

if (train_sou[sou]->STATUS.BIT.SAFE) {

//安全でないときは次区間に他の列車がかかっているのでONしない。

if (train_sou[sou]->NOW.BIT.DIR == dir) {

if (train_sou[sou]->NEXT.BIT.ROSEN == ROSEN_NUM) {

kukan[sou] |= EnableBit[train_sou[sou]->NEXT.BIT.KUKAN];

}

//区間ON用

void kukan_ON(unsigned char sou, unsigned char d) {

if (train_sou[sou]) {

if (train_sou[sou]->NOW.BIT.DIR == d) {

// d=0:正回転, 1:負回転

if (d == 0) {

LATB |= kukan[sou];

_LATB12 = 0; //Port RB12は共通側

} else {

LATB &= ~kukan[sou];

_LATB12 = 1;

}

TRISB &= ~kukan[sou];

_TRISB12 = 0;

}

void section_change_monitor(unsigned char sou, unsigned char dir) {

static char sum_count;

static int gnd_sum;

if (train_sou[sou]) {

if (train_sou[sou^1]) //相手変更中は変更しない

if (train_sou[sou^1]->henka) return;

if (train_sou[sou]->NOW.BIT.DIR == dir) {

char chg_enable = 0;

if (train_sou[sou^0x1]) {

//向き合いの時区間変更許可

if (train_sou[sou]->NOW.BIT.DIR != train_sou[sou^0x1]->NOW.BIT.DIR)

chg_enable = 1;

}

if (train_sou[sou]->STATUS.BIT.SAFE || chg_enable)

if (!train_sou[sou]->henka) {

if (train_sou[sou]->NEXT.BIT.ROSEN == ROSEN_NUM) {

//次位置区間の監視

kanshi.BIT.KUKAN = train_sou[sou]->NEXT.BIT.KUKAN;

LATA &= 0xC3;

LATA |= kanshi.BYTE;

//ADC読み込み

BSP_DelayUs(1);

//_RB14 = 1;

PLIB_ADC_SamplingStart(ADC_ID_1);

while (!PLIB_ADC_ConversionHasCompleted(ADC_ID_1));

adc_ret.INT = PLIB_ADC_ResultGetByIndex(ADC_ID_1, 0);

//_RB14 = 0;

if (train_sou[sou]->NOW.BIT.DIR == 0) {

//正方向のとき

if (adc_ret.INT >= 0x280) {

train_sou[sou]->henka = 0x80; //区間変化

}

//if (sou == 0)debug1.INT = adc_ret.INT;

//else debug2.INT = adc_ret.INT;

} else {

//逆方向のとき

if (adc_ret.INT < 0x180) {

train_sou[sou]->henka = 0x80; //区間変化

}

//if (sou == 0)debug1.INT = adc_ret.INT;

//else debug2.INT = adc_ret.INT;

}

//区間変化でないときGND値とする。

// if (!train_sou[sou]->henka) {

// gnd_adc = adc_ret.INT;

// //区間変更なしのときのADC値をGND Levelにします。

// //16回たして4bit右シフトで平均をとります。

// gnd_sum += adc_ret.INT;

// if (sum_count++ == 15) {

// gnd_level.INT = gnd_sum >> 4;

// sum_count = 0;

// gnd_sum = 0;

// }

}

void next_section_on(unsigned char sou, unsigned char dir) {

//次区間をON

if (train_sou[sou]) {

if (train_sou[sou]->NOW.BIT.DIR == dir) {

if (train_sou[sou]->STATUS.BIT.SAFE) {

//安全でないときは次区間に他の列車がかかっているのでONしない。

if (train_sou[sou]->NEXT.BIT.ROSEN == ROSEN_NUM) {

kukan[sou] |= EnableBit[train_sou[sou]->NEXT.BIT.KUKAN];

//kukan_ON(kukan[sou], train_sou[sou]->NOW.BIT.DIR);

}

void read_generated_voltage(unsigned char n, unsigned char sou) {

static unsigned char count[2], p[2], count_B[2];

static int speed_buf[2][32]; //16

static int read_speed[2];

static int speed_sou[2]; //相手のスピード

char m;

if (train_sou[sou]) {

char sou_b = 0;

if (sou == 0) sou_b = 1;

//現位置と前位置を交互に読み込み

if (n == 0) {//n == 0

kanshi.BIT.KUKAN = kanshi_now[sou];

//kanshi.BIT.KUKAN = train_sou[sou]->NOW.BIT.KUKAN;

} else {

kanshi.BIT.KUKAN = kanshi_before[sou];

//kanshi.BIT.KUKAN = train_sou[sou]->BEFORE.BIT.KUKAN;

}

// LATA &= 0xC3;

// LATA |= kanshi.BYTE;

PORTA = kanshi.BYTE;

//BSP_DelayUs(1);

//ADC読み込み

PLIB_ADC_SamplingStart(ADC_ID_1);

while (!PLIB_ADC_ConversionHasCompleted(ADC_ID_1));

adc_ret.INT = PLIB_ADC_ResultGetByIndex(ADC_ID_1, 0);

//ADC値からGND値を引いて絶対値をとります。

adc_ret.INT = adc_ret.INT - gnd_level.INT;

if (adc_ret.INT < 0)

adc_ret.INT = -adc_ret.INT;

//8回のピーク値をスピードデータにします。

// if (count[sou]++ == 7) {

// read_speed[sou] = adc_ret.INT;

// count[sou] = 0;

// } else if (adc_ret.INT > read_speed[sou]) {

// read_speed[sou] = adc_ret.INT;

// return; //ここで終了

// }

//8回のピーク値をスピードデータにします。

if (adc_ret.INT > read_speed[sou]) {

read_speed[sou] = adc_ret.INT;

}

speed_sou[sou] = read_speed[sou];

// p[sou]++;

// if (p[sou] == 16) p[sou] = 0;

// speed_buf[sou][p[sou]] = read_speed[sou]; //0xf

speed_buf[sou][++p[sou] & 0xf] = read_speed[sou]; //0xf

//peek reset

if (++count[sou] == 8) {

read_speed[sou] = adc_ret.INT;

count[sou] = 0;

}

//移動平均

//char m;

unsigned long avr = 0;

for (m = 0; m < 16; m++) {//16

avr += speed_buf[sou][m];

}

avr >>= 4; //4

//avr = read_speed[sou];

//読み取り電圧補正

// if (volt_kb.INT < 0x100 || volt_kb.INT > 0x280)

// volt_kb.INT = 0x150;

// avr = avr * volt_kb.INT;

// avr = avr / 0x100;

//train_sou[sou]->speed_ret.INT = avr; //4

if (count_B[sou]++ == 15) {

count_B[sou] = 0;

if (avr < train_sou[sou]->speed_ret.INT) {

train_sou[sou]->speed_ret.INT--;

} else if (avr > train_sou[sou]->speed_ret.INT)

train_sou[sou]->speed_ret.INT++;

}

if (train_sou[sou]->NOW.BIT.ROSEN == ROSEN_NUM) {

if (train_sou[sou]->NOW.BIT.ROSEN != train_sou[sou]->BEFORE.BIT.ROSEN) {

if (train_sou[sou]->speed_ret_rx.INT > train_sou[sou]->speed_ret.INT) {

train_sou[sou]->speed_ret.INT = train_sou[sou]->speed_ret_rx.INT;

}

void speed_cont(unsigned char sou) {

int err; //スピードのエラー

// int err_abs; //err絶対値

int d; //エラー補正値

static char count[2];

static char count_avr[2];

if (!train_sou[sou])return;

// スピード設定値と実際スピードの比較

err = train_sou[sou]->speed - train_sou[sou]->speed_ret.INT;

err_buff[sou][count_avr[sou]++ & 0xF] = err;

//---error avrage---

int err_sum = 0;

char c;

for (c = 0; c < 16; c++) {

err_sum += err_buff[sou][c];

}

err_avr[sou].INT = err_sum / 16;

// err_abs = err_avr[sou].INT;

// if (err_abs < 0)err_abs = -err_abs;

//--test--

//d = (err * err_avr[sou].INT) / 0x80;

//d = err_avr[sou].INT / 0x10;

d = err_avr[sou].INT / 4; // /10

int d_max = 0x50; //+補正最大値

//int d_max_m = 0x100; //-補正最大値

char cont_t = 10; //制御間隔

//動き出しを早く

if (train_sou[sou]->speed_ret.INT < 10) {

d_max = 0x100;

cont_t = 2;

}

// if (d > d_max)d = d_max;

// else if (d < -d_max_m)d = -d_max_m;

//スピード設定が０のとき補正値が負でない場合

//完全に停止させるため補正値を-1にします

#define d_zero -20

if (train_sou[sou]->speed == 0) {

cont_t = 2; //減速早く 2

if (d > d_zero)//-3

d = d_zero; //-0x3

} else {

//if (err_avr[sou].INT < train_sou[sou]->err_th)return;

//if (err_abs < train_sou[sou]->err_th)return;

}

//if (d < 0) cont_t = 20; //減速は早く

//スピードコントロール値をエラー補正値で補正

if (++count[sou] > cont_t) {//10

count[sou] = 0;

train_sou[sou]->speed_cont.INT += d;

} else {

return;

}

//結果が負にならないようにする

if (train_sou[sou]->speed_cont.INT < 0)

train_sou[sou]->speed_cont.INT = 0;

//接触不良時の制限

if (train_sou[sou]->speed_ret.INT < 0x4) {

int contact_fail = SPEED_MAX * 10 / 10; //max/2

if (train_sou[sou]->speed_cont.INT > contact_fail)

train_sou[sou]->speed_cont.INT = contact_fail;

}

//Speedの最大値を制限

if (train_sou[sou]->speed_cont.INT > SPEED_MAX) {

train_sou[sou]->speed_cont.INT = SPEED_MAX;

}

//extra_power

if (train_sou[sou]->speed_cont.INT > SPEED_MAX - 0x20) {

if (ext_pwr[sou] < 0xc0) {

if ((count_avr[sou] & 0xf) == 0) ext_pwr[sou]++;

}

} else {

if (ext_pwr[sou] > 0) {

ext_pwr[sou]--;

}

//ext_pwr[sou] = 0; //test

}

void section_change() {

char n;

// if (chg_disable) return;

for (n = 0; n < TR_COUNT; n++) {

if (train[n].STATUS.BIT.CHG == 1) {

//受信データに置き換え

train[n].BEFORE.BYTE = train[n].REC_BEFORE;

train[n].NOW.BYTE = train[n].REC_NOW;

train[n].NEXT.BYTE = train[n].REC_NEXT;

if (cont_train[0] == n) {

cont_train[0] = 0xff;

train_sou[0] = NULL;

}

if (cont_train[1] == n) {

cont_train[1] = 0xff;

train_sou[1] = NULL;

}

if ((train[n].NOW.BIT.ROSEN == ROSEN_NUM)

|| (train[n].NEXT.BIT.ROSEN == ROSEN_NUM)

|| (train[n].BEFORE.BIT.ROSEN == ROSEN_NUM)) {

//各相の列車登録

cont_train[train[n].NOW.BIT.SOU] = n;

train_sou[train[n].NOW.BIT.SOU] = &train[n];

} else {

train[n].speed_cont.INT = 0;

}

train[n].henka = 0;

train[n].STATUS.BIT.CHG = 0;

}

//kukan clr

kukan[0] = 0;

kukan[1] = 0;

//check same dir

if (train_sou[0] && train_sou[1]) {//両相ともON?

if (train_sou[0]->NOW.BIT.DIR == train_sou[1]->NOW.BIT.DIR) {//same dir?

if (same_dir_mode < 0x80 && inc_interval++ > 50) {

same_dir_mode++;

inc_interval = 0;

}

same_dir = train_sou[0]->NOW.BIT.DIR; //set dir

} else {

same_dir_mode = 0;

inc_interval = 0;

}

} else {

//one side only

if (same_dir_mode < 0x80 && inc_interval++ > 50) {

same_dir_mode++;

inc_interval = 0;

}

if (train_sou[0]) {

same_dir = train_sou[0]->NOW.BIT.DIR;

}

if (train_sou[1]) {

same_dir = train_sou[1]->NOW.BIT.DIR;

}

void board_comm(unsigned char rec_bit) {

unsigned char bit_p;

unsigned int data_p;

data_p = (comm_counter - 1) & 0x3ff;

bit_p = EnableBit[data_p & 7]; //bit位置set

data_p >>= 3;

board_num = data_p;

board_num >>= 4;

#if ROSEN_NUM == 0

//親ボードのみポイントなどのボードに送信

if (!(board_num == ROSEN_NUM || board_num == 6)) {

#else

if (!(board_num == ROSEN_NUM)) {

#endif

//データ受信

_TRISB11 = 1;

if (rec_bit)

receive_data |= bit_p;

else

receive_data &= ~bit_p;

if (bit_p == 0x80) {

comm_data[data_p] = receive_data;

}

//ボード間データ通信

data_p = comm_counter & 0x3ff;

bit_p = EnableBit[data_p & 7]; //bit位置set

data_p >>= 3;

board_num = data_p;

board_num >>= 4;

#if ROSEN_NUM == 0

//親ボードのみポイントなどのボードに送信

if (board_num == ROSEN_NUM || board_num == 6) {

#else

if (board_num == ROSEN_NUM) {

#endif

//データ送信

_TRISB11 = 0;

send_data = comm_data[data_p];

//送信PORTデータセット

if (send_data & bit_p)

_RB11 = 1;

else

_RB11 = 0;

}

void comm_data_set_tx() {

unsigned char n;

unsigned int data_p;

//comm_data 送信データSET

data_p = ROSEN_NUM << 4;

//A相

n = cont_train[0];

if (n != 0xff) {

comm_data[data_p] = n + 0xA0;

comm_data[data_p + 1] = train[n].speed_ret.BYTE.H; //speed_ret_tx

comm_data[data_p + 2] = train[n].speed_ret.BYTE.L;

comm_data[data_p + 3] = train[n].henka;

comm_data[data_p + 4] = train[n].speed_cont.BYTE.H;

comm_data[data_p + 5] = train[n].speed_cont.BYTE.L;

comm_data[data_p + 6] = train[n].NOW.BYTE;

comm_data[data_p + 7] = ext_pwr[0]; //same_dir_mode

} else

comm_data[data_p] = 0xFF;

//B相

n = cont_train[1];

data_p += 0x8;

if (n != 0xff) {

comm_data[data_p] = n + 0xA0;

comm_data[data_p + 1] = train[n].speed_ret.BYTE.H; //speed_ret_tx

comm_data[data_p + 2] = train[n].speed_ret.BYTE.L;

comm_data[data_p + 3] = train[n].henka;

comm_data[data_p + 4] = train[n].speed_cont.BYTE.H;

comm_data[data_p + 5] = train[n].speed_cont.BYTE.L;

comm_data[data_p + 6] = train[n].NOW.BYTE;

} else

comm_data[data_p] = 0xFF;

}

void comm_data_set_rx() {

//受信データSET

unsigned char n;

unsigned int data_p;

for (board_num = 0; board_num < BOARD_COUNT; board_num++) {

if (board_num != ROSEN_NUM) {

//自ボード以外受信

data_p = board_num << 4;

//A相

n = comm_data[data_p];

if ((n & 0xF0) == 0xA0) {

n &= 0xF;

train[n].speed_ret_rx.BYTE.H = comm_data[data_p + 1];

train[n].speed_ret_rx.BYTE.L = comm_data[data_p + 2];

if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {

if (train[n].NOW.BIT.ROSEN == train[n].BEFORE.BIT.ROSEN)

//現位置および前位置が他路線のとき実スピード受信

train[n].speed_ret.INT = train[n].speed_ret_rx.INT;

}

if (ROSEN_NUM == 0)//Masterボードのみ区間変化受信

if (train[n].NEXT.BIT.ROSEN != 0) {

//NextがMasterボード以外のとき受信

if (train[n].NEXT.BIT.ROSEN == board_num)//次区間のボードの区間変化を受信

train[n].henka = comm_data[data_p + 3];

}

train[n].speed_rx.BYTE.H = comm_data[data_p + 4];

train[n].speed_rx.BYTE.L = comm_data[data_p + 5];

if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {

if (train[n].NEXT.BIT.ROSEN == ROSEN_NUM)

//ポイント切り替え時次区間でspeed_cont渡し

train[n].speed_cont.INT = train[n].speed_rx.INT;

}

//B相

data_p += 0x8;

n = comm_data[data_p];

if ((n & 0xF0) == 0xA0) {

n &= 0xF;

train[n].speed_ret_rx.BYTE.H = comm_data[data_p + 1];

train[n].speed_ret_rx.BYTE.L = comm_data[data_p + 2];

if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {

if (train[n].NOW.BIT.ROSEN == train[n].BEFORE.BIT.ROSEN)

//現位置および前位置が他路線のとき実スピード受信

train[n].speed_ret.INT = train[n].speed_ret_rx.INT;

}

if (ROSEN_NUM == 0)//Masterボードのみ区間変化受信

if (train[n].NEXT.BIT.ROSEN != 0) {

//NextがMasterボード以外のとき受信

if (train[n].NEXT.BIT.ROSEN == board_num)//次区間のボードの区間変化を受信

train[n].henka = comm_data[data_p + 3];

}

train[n].speed_rx.BYTE.H = comm_data[data_p + 4];

train[n].speed_rx.BYTE.L = comm_data[data_p + 5];

if (train[n].NOW.BIT.ROSEN != ROSEN_NUM) {

if (train[n].NEXT.BIT.ROSEN == ROSEN_NUM)

//ポイント切り替え時次区間でspeed_cont渡し

train[n].speed_cont.INT = train[n].speed_rx.INT;

}

#if ROSEN_NUM == 0

//point_request

if (point_req) {

if (!comm_data[0x70]) {

//ready

comm_data[0x60] = point_req; //point_data

} else

//busy

if (comm_data[0x60]) {

//リクエストクリア

point_req = 0;

comm_data[0x60] = 0;

}

//yardt_request

if (yard_req) {

if (!comm_data[0x71]) {

//ready

comm_data[0x61] = yard_req; //point_data

} else

//busy

if (comm_data[0x61]) {

//リクエストクリア

yard_req = 0;

comm_data[0x61] = 0;

}

#endif

}

//ポイント制御

void point_cont() {

unsigned char n;

if (!point_req) {

for (n = 0; n < TR_COUNT; n++) {

if ((train[n].point & 0x80) != 0) {

point_req = train[n].point;

train[n].point = 0;

break;

}

//ヤード制御

void yard_cont() {

unsigned char n;

if (!yard_req) {

for (n = 0; n < TR_COUNT; n++) {

if ((train[n].yard & 0x80) != 0) {

yard_req = train[n].yard;

train[n].yard = 0;

break;

}

//pulse off用インタラプトFunction

void timer2_int_func(char s) {

if (s == 0) {//TM1

if (section1) TRISB |= section1;

DRV_TMR1_Stop();

if (both_off) {//2列車のSpeedPulse幅の差がないときはどちらか早いほうのTimerでPulseOFF

do {

timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

} while (timer_value.INT < sp_w2);

if (section2) TRISB |= section2;

}

} else {//TM2

if (section2) TRISB |= section2;

DRV_TMR2_Stop();

if (both_off) {//2列車のSpeedPulse幅の差がないときはどちらか早いほうのTimerでPulseOFF

do {

timer_value.INT = TMR_Counter16BitGet_In16BitRegister(TMR_ID_1);

} while (timer_value.INT < sp_w1);

if (section1) TRISB |= section1;

}

/* *****************************************************************************

End of File

・app.cを編集します。void APP_Tasks ( void )以下をすげ変えます。

//
//
//2022_0612 app.cすげ替え

/******************************************************************************
  Function:
    void APP_Tasks ( void )

  Remarks:
    See prototype in app.h.
 */

void ini_train(void);
void train_set(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char);

void APP_Tasks(void) {
    static unsigned char buf_p;

    /* Check the application's current state. */
    switch (appData.state) {
            /* Application's initial state. */
        case APP_STATE_INIT:
        {
            bool appInitialized = true;


            DRV_ADC_Open(); //Enable ADC

            //USART
            if (handleUSART0 == DRV_HANDLE_INVALID) {
                handleUSART0 = DRV_USART_Open(0, DRV_IO_INTENT_READWRITE | DRV_IO_INTENT_NONBLOCKING);
                appInitialized &= (DRV_HANDLE_INVALID != handleUSART0);
            }

            //I2C Open
            hi2c = DRV_I2C_Open(DRV_I2C_INDEX_0, DRV_IO_INTENT_READWRITE | DRV_IO_INTENT_NONBLOCKING);
            if (hi2c != DRV_HANDLE_INVALID) {
                //LCD初期化
                LCD_int();
                LCD_str("PC_REM");
            }


            gnd_level.INT = 0x200;

            DRV_TMR0_Start(); //TimerStart
#if ROSEN_NUM==0
            //DRV_TMR0_Start(); //TimerStart
#else
            //マスターボード以外はEXT_INT
            ext_int_enable = true;
            _TRISB14 = 0;
#endif

            //PLIB_TMR_Period16BitSet(TMR_ID_2, 0x7000);
            //DRV_TMR1_Start(); //PULSE OFF TimerStart

            //-----ATC-------
            cont_train[0] = 0xff;
            cont_train[1] = 0xff;

            train_sou[0] = NULL;
            train_sou[1] = NULL;

            ini_train();



            //列車A相
            //            train[0].mascon = 0x18; //スピードを変える時はここを変更
            //            train_set(0, 0, 1, 0, 0); //n,rosen,section,dir,sou

            //列車B相
            //            train[1].mascon = 0x1c; //スピードを変える時はここを変更
            //            train_set(1, 0, 5, 0, 1); //n,rosen,section,dir,sou


            if (appInitialized) {

                appData.state = APP_STATE_SERVICE_TASKS;
            }
            break;
        }

        case APP_STATE_SERVICE_TASKS:
        {
            unsigned char n, p;
            unsigned char ret;
            union byte_access time_out;
            long count;

            rx_data[0] = 0;
            rx_data[1] = 0;
            time_out.INT = 0;

            U1STAbits.OERR = 0; //受信バッファ・エラークリア

            ret = 0;
            while (ret != 0x55) {
                //0x55が来るまでずーと待つ
                while (!DRV_USART_ReceiverBufferIsEmpty(DRV_USART_INDEX_0)) {
                    ret = DRV_USART_ReadByte(DRV_USART_INDEX_0);
                }
            }


            for (n = 1; n < RX_BYTE; n++) {
                count = 0;
                while (DRV_USART_ReceiverBufferIsEmpty(DRV_USART_INDEX_0)) {
                    if (count++ > 0xfffff)break;
                }
                if (count > 0xfffff)break; //TimeOutで外へ

                rx_data[n] = DRV_USART_ReadByte(DRV_USART_INDEX_0);
            }

            chg_disable = 0; //INT中の変更禁止

            if (rx_data[1] == 0xAA) {
                //ヘッダー正常(0x55 0xAA)
                time_out.INT = count;

                for (n = 0; n < TR_COUNT; n++) {
                    p = n * RX_DATA_BYTE + 2;
                    train[n].mascon = rx_data[p];
                    train[n].speed = train[n].mascon;
                    train[n].REC_NOW = rx_data[p + 1];
                    train[n].REC_BEFORE = rx_data[p + 2];
                    train[n].REC_NEXT = rx_data[p + 3];
                    train[n].err_th = 0x10;

                    //区間変更フラグクリア
                    if (rx_data[p + 4] & 1) {
                        train[n].STATUS.BIT.CHG = 1;
                    }

                    //安全フラグ
                    if (rx_data[p + 4] & 0x80)
                        train[n].STATUS.BIT.SAFE = 0x1;
                    else
                        train[n].STATUS.BIT.SAFE = 0;

                    //MANU SPEED
                    if (rx_data[p + 4] & 0b10) {
                        train[n].STATUS.BIT.SP_MANU = 0x1;
                        train[n].speed = train[n].mascon * 0xE8 / 100;
                    } else
                        train[n].STATUS.BIT.SP_MANU = 0;



                    //point_request
                    if (rx_data[p + 5])
                        train[n].point = rx_data[p + 5];
                    //yard_request
                    if (rx_data[p + 6])
                        train[n].yard = rx_data[p + 6];


                }
                chg_disable = 0; //INT中の変更可

                //オシロスコープ用TRG
                osc_trg.BYTE.H = rx_data[100];
                osc_trg.BYTE.L = rx_data[101];

                ext_time = rx_data[102]*256;
                ext_time += rx_data[103];


                //232送信
                tx_data[0] = 0x55; //ヘッダー0x55,0xAA
                tx_data[1] = 0xAA;

                for (n = 0; n < TR_COUNT; n++) {
                    p = n * TX_DATA_BYTE + 2;
                    //区間変化情報の送信
                    tx_data[p + 2] = train[n].henka;
                    tx_data[p + 3] = train[n].point;
                    tx_data[p + 4] = train[n].yard;

                    //スピード読み取り値の送信


                    if (train[n].NOW.BIT.ROSEN == ROSEN_NUM) {
                        tx_data[p] = train[n].speed_ret.BYTE.H;
                        tx_data[p + 1] = train[n].speed_ret.BYTE.L;
                        tx_data[p + 5] = train[n].speed_cont.BYTE.H;
                        tx_data[p + 6] = train[n].speed_cont.BYTE.L;
                    } else {
                        //他のボードのときcomm_dataのcont_speedを送る
                        tx_data[p] = train[n].speed_ret_rx.BYTE.H;
                        tx_data[p + 1] = train[n].speed_ret_rx.BYTE.L;
                        tx_data[p + 5] = train[n].speed_rx.BYTE.H;
                        tx_data[p + 6] = train[n].speed_rx.BYTE.L;
                    }
                }



                for (n = 0; n < 128; n++) {
                    tx_data[100 + n] = comm_data[n];
                }

                //Degug
                tx_data[100 + 0x30] = 55;
                if (train_sou[0]) tx_data[100 + 0x31] = train_sou[0]->STATUS.BYTE;
                else tx_data[100 + 0x31] = 0xff;
                if (train_sou[1]) tx_data[100 + 0x32] = train_sou[1]->STATUS.BYTE;
                else tx_data[100 + 0x32] = 0xff;


                // 送信用メモリデータをPCに転送します
                for (n = 0; n < TX_BYTE; n++) {
                    DRV_USART_WriteByte(DRV_USART_INDEX_0, tx_data[n]);
                }

            }


            BSP_DelayMs(20);

            //Debug用LCD表示
            LCD_posyx(0, 0);

            //debug1.INT = gnd_level.INT;

            LCD_hex(int_count1.BYTE.H);
            LCD_hex(int_count1.BYTE.L);
            LCD_hex(int_count2.BYTE.H);
            LCD_hex(int_count2.BYTE.L);

            //LCD_hex(debug1.BYTE.H);
            //LCD_hex(debug1.BYTE.L);
            //LCD_hex(debug2.BYTE.H);
            //LCD_hex(debug2.BYTE.L);
            //LCD_hex(train[0].henka);

            union byte_access err_abs;
            err_abs.INT = err_avr[0].INT;
            if (err_abs.INT < 0)err_abs.INT = -err_abs.INT;

            //LCD_hex(err_abs.BYTE.H);
            //LCD_hex(err_abs.BYTE.L);


            //LCD_str(" ");
            LCD_hex(timer_value.BYTE.H);
            LCD_hex(timer_value.BYTE.L);
            //
            //            if (err_abs.INT < train[0].err_th)
            //                LCD_str(" OFF ");
            //            else
            //                LCD_str(" ON  ");

            LCD_posyx(1, 0);
            LCD_hex(train[0].NOW.BYTE);
            LCD_hex(train[0].NEXT.BYTE);

            LCD_hex(train[1].NOW.BYTE);
            LCD_hex(train[1].NEXT.BYTE);

            break;
        }
            /* TODO: implement your application state machine.*/


            /* The default state should never be executed. */
        default:
        {
            /* TODO: Handle error in application's state machine. */
            break;
        }
    }
}

void ini_train() {
    char n;

    for (n = 0; n < TR_COUNT; n++) {
        train[n].BEFORE.BYTE = 0x38;
        train[n].NOW.BYTE = 0x38;
        train[n].NEXT.BYTE = 0x38;
        train[n].ANEXT.BYTE = 0x38;
        train[n].STATUS.BYTE = 0;
        train[n].speed = 0;
        train[n].henka = 0;
    }

}

void train_set(unsigned char n, unsigned char rosen, unsigned char sec, unsigned char dir, unsigned char sou) {
    train[n].NOW.BIT.ROSEN = rosen;
    train[n].NOW.BIT.KUKAN = sec;
    train[n].NOW.BIT.DIR = dir;
    train[n].NOW.BIT.SOU = sou;

    train[n].BEFORE.BYTE = train[n].NOW.BYTE;
    train[n].NEXT.BYTE = train[n].NOW.BYTE;
    train[n].ANEXT.BYTE = train[n].NOW.BYTE;

    if (dir) {
        //逆転 
        train[n].BEFORE.BIT.KUKAN++;
        train[n].NEXT.BIT.KUKAN--;
        train[n].ANEXT.BIT.KUKAN = train[n].NOW.BIT.KUKAN - 2;
    } else {
        //正転
        train[n].BEFORE.BIT.KUKAN--;
        train[n].NEXT.BIT.KUKAN++;
        train[n].ANEXT.BIT.KUKAN += 2;
    }

    train[n].STATUS.BIT.CHG = 0;
    train[n].STATUS.BIT.SAFE = 1;

}


/*******************************************************************************
 End of File
 */

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

256

257

258

259

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

275

276

277

278

279

280

281

282

283

284

285

286

287

288

289

290

291

292

293

294

295

296

297

298

299

300

301

302

303

304

305

306

307

308

309

310

311

312

313

314

315

316

317

318

319

320

321

322

//2022_0612 app.cすげ替え

/******************************************************************************

Function:

void APP_Tasks ( void )

Remarks:

See prototype in app.h.

void ini_train(void);

void train_set(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char);

void APP_Tasks(void) {

static unsigned char buf_p;

/* Check the application's current state. */

switch (appData.state) {

/* Application's initial state. */

case APP_STATE_INIT:

{

bool appInitialized = true;

DRV_ADC_Open(); //Enable ADC

//USART

if (handleUSART0 == DRV_HANDLE_INVALID) {

handleUSART0 = DRV_USART_Open(0, DRV_IO_INTENT_READWRITE | DRV_IO_INTENT_NONBLOCKING);

appInitialized &= (DRV_HANDLE_INVALID != handleUSART0);

}

//I2C Open

hi2c = DRV_I2C_Open(DRV_I2C_INDEX_0, DRV_IO_INTENT_READWRITE | DRV_IO_INTENT_NONBLOCKING);

if (hi2c != DRV_HANDLE_INVALID) {

//LCD初期化

LCD_int();

LCD_str("PC_REM");

}

gnd_level.INT = 0x200;

DRV_TMR0_Start(); //TimerStart

#if ROSEN_NUM==0

//DRV_TMR0_Start(); //TimerStart

#else

//マスターボード以外はEXT_INT

ext_int_enable = true;

_TRISB14 = 0;

#endif

//PLIB_TMR_Period16BitSet(TMR_ID_2, 0x7000);

//DRV_TMR1_Start(); //PULSE OFF TimerStart

//-----ATC-------

cont_train[0] = 0xff;

cont_train[1] = 0xff;

train_sou[0] = NULL;

train_sou[1] = NULL;

ini_train();

//列車A相

// train[0].mascon = 0x18; //スピードを変える時はここを変更

// train_set(0, 0, 1, 0, 0); //n,rosen,section,dir,sou

//列車B相

// train[1].mascon = 0x1c; //スピードを変える時はここを変更

// train_set(1, 0, 5, 0, 1); //n,rosen,section,dir,sou

if (appInitialized) {

appData.state = APP_STATE_SERVICE_TASKS;

}

break;

}

case APP_STATE_SERVICE_TASKS:

{

unsigned char n, p;

unsigned char ret;

union byte_access time_out;

long count;

rx_data[0] = 0;

rx_data[1] = 0;

time_out.INT = 0;

U1STAbits.OERR = 0; //受信バッファ・エラークリア

ret = 0;

while (ret != 0x55) {

//0x55が来るまでずーと待つ

while (!DRV_USART_ReceiverBufferIsEmpty(DRV_USART_INDEX_0)) {

ret = DRV_USART_ReadByte(DRV_USART_INDEX_0);

}

for (n = 1; n < RX_BYTE; n++) {

count = 0;

while (DRV_USART_ReceiverBufferIsEmpty(DRV_USART_INDEX_0)) {

if (count++ > 0xfffff)break;

}

if (count > 0xfffff)break; //TimeOutで外へ

rx_data[n] = DRV_USART_ReadByte(DRV_USART_INDEX_0);

}

chg_disable = 0; //INT中の変更禁止

if (rx_data[1] == 0xAA) {

//ヘッダー正常(0x55 0xAA)

time_out.INT = count;

for (n = 0; n < TR_COUNT; n++) {

p = n * RX_DATA_BYTE + 2;

train[n].mascon = rx_data[p];

train[n].speed = train[n].mascon;

train[n].REC_NOW = rx_data[p + 1];

train[n].REC_BEFORE = rx_data[p + 2];

train[n].REC_NEXT = rx_data[p + 3];

train[n].err_th = 0x10;

//区間変更フラグクリア

if (rx_data[p + 4] & 1) {

train[n].STATUS.BIT.CHG = 1;

}

//安全フラグ

if (rx_data[p + 4] & 0x80)

train[n].STATUS.BIT.SAFE = 0x1;

else

train[n].STATUS.BIT.SAFE = 0;

//MANU SPEED

if (rx_data[p + 4] & 0b10) {

train[n].STATUS.BIT.SP_MANU = 0x1;

train[n].speed = train[n].mascon * 0xE8 / 100;

} else

train[n].STATUS.BIT.SP_MANU = 0;

//point_request

if (rx_data[p + 5])

train[n].point = rx_data[p + 5];

//yard_request

if (rx_data[p + 6])

train[n].yard = rx_data[p + 6];

}

chg_disable = 0; //INT中の変更可

//オシロスコープ用TRG

osc_trg.BYTE.H = rx_data[100];

osc_trg.BYTE.L = rx_data[101];

ext_time = rx_data[102]*256;

ext_time += rx_data[103];

//232送信

tx_data[0] = 0x55; //ヘッダー0x55,0xAA

tx_data[1] = 0xAA;

for (n = 0; n < TR_COUNT; n++) {

p = n * TX_DATA_BYTE + 2;

//区間変化情報の送信

tx_data[p + 2] = train[n].henka;

tx_data[p + 3] = train[n].point;

tx_data[p + 4] = train[n].yard;

//スピード読み取り値の送信

if (train[n].NOW.BIT.ROSEN == ROSEN_NUM) {

tx_data[p] = train[n].speed_ret.BYTE.H;

tx_data[p + 1] = train[n].speed_ret.BYTE.L;

tx_data[p + 5] = train[n].speed_cont.BYTE.H;

tx_data[p + 6] = train[n].speed_cont.BYTE.L;

} else {

//他のボードのときcomm_dataのcont_speedを送る

tx_data[p] = train[n].speed_ret_rx.BYTE.H;

tx_data[p + 1] = train[n].speed_ret_rx.BYTE.L;

tx_data[p + 5] = train[n].speed_rx.BYTE.H;

tx_data[p + 6] = train[n].speed_rx.BYTE.L;

}

for (n = 0; n < 128; n++) {

tx_data[100 + n] = comm_data[n];

}

//Degug

tx_data[100 + 0x30] = 55;

if (train_sou[0]) tx_data[100 + 0x31] = train_sou[0]->STATUS.BYTE;

else tx_data[100 + 0x31] = 0xff;

if (train_sou[1]) tx_data[100 + 0x32] = train_sou[1]->STATUS.BYTE;

else tx_data[100 + 0x32] = 0xff;

// 送信用メモリデータをPCに転送します

for (n = 0; n < TX_BYTE; n++) {

DRV_USART_WriteByte(DRV_USART_INDEX_0, tx_data[n]);

}

BSP_DelayMs(20);

//Debug用LCD表示

LCD_posyx(0, 0);

//debug1.INT = gnd_level.INT;

LCD_hex(int_count1.BYTE.H);

LCD_hex(int_count1.BYTE.L);

LCD_hex(int_count2.BYTE.H);

LCD_hex(int_count2.BYTE.L);

//LCD_hex(debug1.BYTE.H);

//LCD_hex(debug1.BYTE.L);

//LCD_hex(debug2.BYTE.H);

//LCD_hex(debug2.BYTE.L);

//LCD_hex(train[0].henka);

union byte_access err_abs;

err_abs.INT = err_avr[0].INT;

if (err_abs.INT < 0)err_abs.INT = -err_abs.INT;

//LCD_hex(err_abs.BYTE.H);

//LCD_hex(err_abs.BYTE.L);

//LCD_str(" ");

LCD_hex(timer_value.BYTE.H);

LCD_hex(timer_value.BYTE.L);

// if (err_abs.INT < train[0].err_th)

// LCD_str(" OFF ");

// else

// LCD_str(" ON ");

LCD_posyx(1, 0);

LCD_hex(train[0].NOW.BYTE);

LCD_hex(train[0].NEXT.BYTE);

LCD_hex(train[1].NOW.BYTE);

LCD_hex(train[1].NEXT.BYTE);

break;

}

/* TODO: implement your application state machine.*/

/* The default state should never be executed. */

default:

{

/* TODO: Handle error in application's state machine. */

break;

}

void ini_train() {

char n;

for (n = 0; n < TR_COUNT; n++) {

train[n].BEFORE.BYTE = 0x38;

train[n].NOW.BYTE = 0x38;

train[n].NEXT.BYTE = 0x38;

train[n].ANEXT.BYTE = 0x38;

train[n].STATUS.BYTE = 0;

train[n].speed = 0;

train[n].henka = 0;

}

void train_set(unsigned char n, unsigned char rosen, unsigned char sec, unsigned char dir, unsigned char sou) {

train[n].NOW.BIT.ROSEN = rosen;

train[n].NOW.BIT.KUKAN = sec;

train[n].NOW.BIT.DIR = dir;

train[n].NOW.BIT.SOU = sou;

train[n].BEFORE.BYTE = train[n].NOW.BYTE;

train[n].NEXT.BYTE = train[n].NOW.BYTE;

train[n].ANEXT.BYTE = train[n].NOW.BYTE;

if (dir) {

//逆転

train[n].BEFORE.BIT.KUKAN++;

train[n].NEXT.BIT.KUKAN--;

train[n].ANEXT.BIT.KUKAN = train[n].NOW.BIT.KUKAN - 2;

} else {

//正転

train[n].BEFORE.BIT.KUKAN--;

train[n].NEXT.BIT.KUKAN++;

train[n].ANEXT.BIT.KUKAN += 2;

}

train[n].STATUS.BIT.CHG = 0;

train[n].STATUS.BIT.SAFE = 1;

}

/*******************************************************************************

End of File

・system_interrupt.cの後ろのほうを編集します。

//
//
//2022_0903 system_interrupt.c 編集

void __ISR(_EXTERNAL_1_VECTOR, IPL6AUTO) _IntHandlerExternalInterruptInstance0(void)
{
    PLIB_INT_SourceFlagClear(INT_ID_0, INT_SOURCE_EXTERNAL_1);
    
    if (ext_int_enable)
        timer_int_func();
}
 

void __ISR(_TIMER_1_VECTOR, ipl7AUTO) IntHandlerDrvTmrInstance0(void)
{
    PLIB_INT_SourceFlagClear(INT_ID_0,INT_SOURCE_TIMER_1);
    
    timer_int_func();
}
void __ISR(_TIMER_2_VECTOR, ipl5AUTO) IntHandlerDrvTmrInstance1(void)
{
    PLIB_INT_SourceFlagClear(INT_ID_0,INT_SOURCE_TIMER_2);
     timer2_int_func(0);
    int_count1.INT--;
    debug1.INT = 0xff;
    
}
void __ISR(_TIMER_4_VECTOR, ipl5AUTO) IntHandlerDrvTmrInstance2(void)
{
    PLIB_INT_SourceFlagClear(INT_ID_0,INT_SOURCE_TIMER_4);
    timer2_int_func(1);
    int_count2.INT--;
    
}
 /*******************************************************************************
 End of File
*/

//2022_0903 system_interrupt.c 編集

void __ISR(_EXTERNAL_1_VECTOR, IPL6AUTO) _IntHandlerExternalInterruptInstance0(void)

{

PLIB_INT_SourceFlagClear(INT_ID_0, INT_SOURCE_EXTERNAL_1);

if (ext_int_enable)

timer_int_func();

}

void __ISR(_TIMER_1_VECTOR, ipl7AUTO) IntHandlerDrvTmrInstance0(void)

{

PLIB_INT_SourceFlagClear(INT_ID_0,INT_SOURCE_TIMER_1);

timer_int_func();

}

void __ISR(_TIMER_2_VECTOR, ipl5AUTO) IntHandlerDrvTmrInstance1(void)

{

PLIB_INT_SourceFlagClear(INT_ID_0,INT_SOURCE_TIMER_2);

timer2_int_func(0);

int_count1.INT--;

debug1.INT = 0xff;

}

void __ISR(_TIMER_4_VECTOR, ipl5AUTO) IntHandlerDrvTmrInstance2(void)

{

PLIB_INT_SourceFlagClear(INT_ID_0,INT_SOURCE_TIMER_4);

timer2_int_func(1);

int_count2.INT--;

}

/*******************************************************************************

End of File

・PicKit4で動かないときはConfiguration BitsのDEBUGの部分をコメントアウト